feat(versal-net): add support for Xilinx Versal NET platform
New SoC is a78 based with gicv3 and uart over pl011. Communication
interfaces are similar to Versal platform. System starts with Xilinx PLM
firmware which loads TF-A(bl31) to DDR, which is already configured, and
jumps to it. PLM also prepare handoff structure for TF-A with information
what components were load and flags which indicate which EL level SW should
be started.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Akshay Belsare <Akshay.Belsare@amd.com>
Change-Id: I2a16c242a77be6c91be3d198727dc3b9bbb97410
diff --git a/plat/xilinx/versal_net/include/plat_macros.S b/plat/xilinx/versal_net/include/plat_macros.S
new file mode 100644
index 0000000..fb108b6
--- /dev/null
+++ b/plat/xilinx/versal_net/include/plat_macros.S
@@ -0,0 +1,118 @@
+/*
+ * Copyright (c) 2018, ARM Limited and Contributors. All rights reserved.
+ * Copyright (c) 2021-2022, Xilinx, Inc. All rights reserved.
+ * Copyright (C) 2022, Advanced Micro Devices, Inc. All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#ifndef PLAT_MACROS_S
+#define PLAT_MACROS_S
+
+#include <drivers/arm/gic_common.h>
+#include <drivers/arm/gicv2.h>
+#include <drivers/arm/gicv3.h>
+
+#include "../include/platform_def.h"
+
+.section .rodata.gic_reg_name, "aS"
+/* Applicable only to GICv2 and GICv3 with SRE disabled (legacy mode) */
+gicc_regs:
+ .asciz "gicc_hppir", "gicc_ahppir", "gicc_ctlr", ""
+
+/* Applicable only to GICv3 with SRE enabled */
+icc_regs:
+ .asciz "icc_hppir0_el1", "icc_hppir1_el1", "icc_ctlr_el3", ""
+
+/* Registers common to both GICv2 and GICv3 */
+gicd_pend_reg:
+ .asciz "gicd_ispendr regs (Offsets 0x200 - 0x278)\n Offset:\t\t\tvalue\n"
+newline:
+ .asciz "\n"
+spacer:
+ .asciz ":\t\t0x"
+
+ /* ---------------------------------------------
+ * The below utility macro prints out relevant GIC
+ * registers whenever an unhandled exception is
+ * taken in BL31 on Versal NET platform.
+ * Expects: GICD base in x16, GICC base in x17
+ * Clobbers: x0 - x10, sp
+ * ---------------------------------------------
+ */
+ .macro versal_net_print_gic_regs
+ /* Check for GICv3 system register access */
+ mrs x7, id_aa64pfr0_el1
+ ubfx x7, x7, #ID_AA64PFR0_GIC_SHIFT, #ID_AA64PFR0_GIC_WIDTH
+ cmp x7, #1
+ b.ne print_gicv2
+
+ /* Check for SRE enable */
+ mrs x8, ICC_SRE_EL3
+ tst x8, #ICC_SRE_SRE_BIT
+ b.eq print_gicv2
+
+ /* Load the icc reg list to x6 */
+ adr x6, icc_regs
+ /* Load the icc regs to gp regs used by str_in_crash_buf_print */
+ mrs x8, ICC_HPPIR0_EL1
+ mrs x9, ICC_HPPIR1_EL1
+ mrs x10, ICC_CTLR_EL3
+ /* Store to the crash buf and print to console */
+ bl str_in_crash_buf_print
+ b print_gic_common
+
+print_gicv2:
+ /* Load the gicc reg list to x6 */
+ adr x6, gicc_regs
+ /* Load the gicc regs to gp regs used by str_in_crash_buf_print */
+ ldr w8, [x17, #GICC_HPPIR]
+ ldr w9, [x17, #GICC_AHPPIR]
+ ldr w10, [x17, #GICC_CTLR]
+ /* Store to the crash buf and print to console */
+ bl str_in_crash_buf_print
+
+print_gic_common:
+ /* Print the GICD_ISPENDR regs */
+ add x7, x16, #GICD_ISPENDR
+ adr x4, gicd_pend_reg
+ bl asm_print_str
+gicd_ispendr_loop:
+ sub x4, x7, x16
+ cmp x4, #0x280
+ b.eq exit_print_gic_regs
+ bl asm_print_hex
+
+ adr x4, spacer
+ bl asm_print_str
+
+ ldr x4, [x7], #8
+ bl asm_print_hex
+
+ adr x4, newline
+ bl asm_print_str
+ b gicd_ispendr_loop
+exit_print_gic_regs:
+ .endm
+
+ /* ---------------------------------------------
+ * The below required platform porting macro
+ * prints out relevant GIC and CCI registers
+ * whenever an unhandled exception is taken in
+ * BL31.
+ * Clobbers: x0 - x10, x16, x17, sp
+ * ---------------------------------------------
+ */
+ .macro plat_crash_print_regs
+ /*
+ * Empty for now to handle more platforms variant.
+ * Uncomment it when versions are stable
+ */
+ /*
+ mov_imm x17, PLAT_VERSAL_NET_GICD_BASE
+ mov_imm x16, PLAT_VERSAL_NET_GICR_BASE
+ versal_net_print_gic_regs
+ */
+ .endm
+
+#endif /* PLAT_MACROS_S */