diff --git a/drivers/cadence/uart/cdns_console.S b/drivers/cadence/uart/cdns_console.S
index 2c7960d..f727838 100644
--- a/drivers/cadence/uart/cdns_console.S
+++ b/drivers/cadence/uart/cdns_console.S
@@ -27,101 +27,7 @@
  * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
  * POSSIBILITY OF SUCH DAMAGE.
  */
-#include <arch.h>
-#include <asm_macros.S>
-#include <cadence/cdns_uart.h>
 
-        .globl  console_core_init
-        .globl  console_core_putc
-        .globl  console_core_getc
-
-	/* -----------------------------------------------
-	 * int console_core_init(unsigned long base_addr,
-	 * unsigned int uart_clk, unsigned int baud_rate)
-	 * Function to initialize the console without a
-	 * C Runtime to print debug information. This
-	 * function will be accessed by console_init and
-	 * crash reporting.
-	 * We assume that the bootloader already set up
-	 * the HW (baud, ...) and only enable the trans-
-	 * mitter and receiver here.
-	 * In: x0 - console base address
-	 *     w1 - Uart clock in Hz
-	 *     w2 - Baud rate
-	 * Out: return 1 on success else 0 on error
-	 * Clobber list : x1, x2, x3
-	 * -----------------------------------------------
-	 */
-func console_core_init
-	/* Check the input base address */
-	cbz	x0, core_init_fail
-	/* Check baud rate and uart clock for sanity */
-	cbz	w1, core_init_fail
-	cbz	w2, core_init_fail
-
-	/* RX/TX enabled & reset */
-	mov	w3, #(R_UART_CR_TX_EN | R_UART_CR_RX_EN | R_UART_CR_TXRST | R_UART_CR_RXRST)
-	str	w3, [x0, #R_UART_CR]
-
-	mov	w0, #1
-	ret
-core_init_fail:
-	mov	w0, wzr
-	ret
-endfunc console_core_init
-
-	/* --------------------------------------------------------
-	 * int console_core_putc(int c, unsigned long base_addr)
-	 * Function to output a character over the console. It
-	 * returns the character printed on success or -1 on error.
-	 * In : w0 - character to be printed
-	 *      x1 - console base address
-	 * Out : return -1 on error else return character.
-	 * Clobber list : x2
-	 * --------------------------------------------------------
-	 */
-func console_core_putc
-	/* Check the input parameter */
-	cbz	x1, putc_error
-	/* Prepend '\r' to '\n' */
-	cmp	w0, #0xA
-	b.ne	2f
-1:
-	/* Check if the transmit FIFO is full */
-	ldr	w2, [x1, #R_UART_SR]
-	tbnz	w2, #UART_SR_INTR_TFUL_BIT, 1b
-	mov	w2, #0xD
-	str	w2, [x1, #R_UART_TX]
-2:
-	/* Check if the transmit FIFO is full */
-	ldr	w2, [x1, #R_UART_SR]
-	tbnz	w2, #UART_SR_INTR_TFUL_BIT, 2b
-	str	w0, [x1, #R_UART_TX]
-	ret
-putc_error:
-	mov	w0, #-1
-	ret
-endfunc console_core_putc
-
-	/* ---------------------------------------------
-	 * int console_core_getc(unsigned long base_addr)
-	 * Function to get a character from the console.
-	 * It returns the character grabbed on success
-	 * or -1 on error.
-	 * In : x0 - console base address
-	 * Clobber list : x0, x1
-	 * ---------------------------------------------
-	 */
-func console_core_getc
-	cbz	x0, getc_error
-1:
-	/* Check if the receive FIFO is empty */
-	ldr	w1, [x0, #R_UART_SR]
-	tbnz	w1, #UART_SR_INTR_REMPTY_BIT, 1b
-	ldr	w1, [x0, #R_UART_RX]
-	mov	w0, w1
-	ret
-getc_error:
-	mov	w0, #-1
-	ret
-endfunc console_core_getc
+#if !ERROR_DEPRECATED
+#include "./aarch64/cdns_console.S"
+#endif