feat(ls1046a): add new SoC platform ls1046a

The LS1046A is a cost-effective, power-efficient, and highly
integrated system-on-chip (SoC) design that extends the reach
of the NXP value-performance line of QorIQ communications
processors. Featuring power-efficient 64-bit Arm Cortex A72
cores with ECC-protected L1 and L2 cache memories for high
reliability, running up to 1.8 GHz.

Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Signed-off-by: rocket <rod.dorris@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Change-Id: I208d9bf1702410463c2b2630d31d0cd4eb7e8837
diff --git a/plat/nxp/soc-ls1046a/aarch64/ls1046a.S b/plat/nxp/soc-ls1046a/aarch64/ls1046a.S
new file mode 100644
index 0000000..daa0542
--- /dev/null
+++ b/plat/nxp/soc-ls1046a/aarch64/ls1046a.S
@@ -0,0 +1,937 @@
+/*
+ * Copyright 2020-2022 NXP
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ *
+ */
+
+#include <asm_macros.S>
+#include <dcfg_lsch2.h>
+#include <nxp_timer.h>
+#include <plat_gic.h>
+#include <scfg.h>
+
+#include <bl31_data.h>
+#include <plat_psci.h>
+#include <platform_def.h>
+
+#define DAIF_DATA		AUX_01_DATA
+#define TIMER_CNTRL_DATA	AUX_02_DATA
+
+.global soc_init_lowlevel
+.global soc_init_percpu
+.global _soc_core_release
+.global _soc_core_restart
+.global _soc_ck_disabled
+.global _soc_sys_reset
+.global _soc_sys_off
+.global _soc_set_start_addr
+.global _getGICC_BaseAddr
+.global _getGICD_BaseAddr
+.global _soc_core_prep_off
+.global _soc_core_entr_off
+.global _soc_core_exit_off
+.global _soc_core_prep_stdby
+.global _soc_core_entr_stdby
+.global _soc_core_exit_stdby
+.global _soc_core_prep_pwrdn
+.global _soc_core_entr_pwrdn
+.global _soc_core_exit_pwrdn
+.global _soc_clstr_prep_stdby
+.global _soc_clstr_exit_stdby
+.global _soc_clstr_prep_pwrdn
+.global _soc_clstr_exit_pwrdn
+.global _soc_sys_prep_stdby
+.global _soc_sys_exit_stdby
+.global _soc_sys_prep_pwrdn
+.global _soc_sys_pwrdn_wfi
+.global _soc_sys_exit_pwrdn
+
+
+/* This function initialize the soc
+ * in: void
+ * out: void
+ */
+func soc_init_lowlevel
+    ret
+endfunc soc_init_lowlevel
+
+
+/* void soc_init_percpu(void)
+ * this function performs any soc-specific initialization that is needed on
+ * a per-core basis
+ * in:  none
+ * out: none
+ * uses x0, x1, x2, x3
+ */
+func soc_init_percpu
+	mov	x3, x30
+
+	bl	plat_my_core_mask
+	mov	x2, x0
+
+	/* see if this core is marked for prefetch disable */
+	mov	x0, #PREFETCH_DIS_OFFSET
+	bl	_get_global_data  /* 0-1 */
+	tst	x0, x2
+	b.eq	1f
+	bl	_disable_ldstr_pfetch_A72  /* 0 */
+1:
+	mov	x30, x3
+	ret
+endfunc soc_init_percpu
+
+/* part of CPU_ON
+ * this function releases a secondary core from reset
+ * in:   x0 = core_mask_lsb
+ * out:  none
+ * uses: x0, x1, x2, x3
+ */
+func _soc_core_release
+
+#if (TEST_BL31)
+	rbit	w2, w0
+	/* x2 = core mask msb */
+#else
+	mov	x2, x0
+#endif
+	/* write COREBCR */
+	mov	x1, #NXP_SCFG_ADDR
+	rev	w3, w2
+	str	w3, [x1, #SCFG_COREBCR_OFFSET]
+	isb
+
+	/* read-modify-write BRR */
+	mov	x1, #NXP_DCFG_ADDR
+	ldr	w2, [x1, #DCFG_BRR_OFFSET]
+	rev	w3, w2
+	orr	w3, w3, w0
+	rev	w2, w3
+	str	w2, [x1, #DCFG_BRR_OFFSET]
+	isb
+
+	/* send event */
+	sev
+	isb
+	ret
+endfunc _soc_core_release
+
+
+/* part of CPU_ON
+ * this function restarts a core shutdown via _soc_core_entr_off
+ * in:  x0 = core mask lsb (of the target cpu)
+ * out: x0 == 0, on success
+ *      x0 != 0, on failure
+ * uses x0, x1, x2, x3, x4, x5
+ */
+func _soc_core_restart
+	mov	x5, x30
+	mov	x3, x0
+
+	/*
+	 * unset ph20 request in RCPM_PCPH20CLEARR
+	 * this is an lsb-0 register
+	 */
+	ldr	x1, =NXP_RCPM_ADDR
+	rev	w2, w3
+	str	w2, [x1, #RCPM_PCPH20CLRR_OFFSET]
+	dsb	sy
+	isb
+
+	bl	_getGICD_BaseAddr
+	mov	x4, x0
+
+	/* enable forwarding of group 0 interrupts by setting GICD_CTLR[0] = 1 */
+	ldr	w1, [x4, #GICD_CTLR_OFFSET]
+	orr	w1, w1, #GICD_CTLR_EN_GRP0
+	str	w1, [x4, #GICD_CTLR_OFFSET]
+	dsb	sy
+	isb
+
+
+	/*
+	 * fire SGI by writing to GICD_SGIR the following values:
+	 * [25:24] = 0x0 (forward interrupt to the CPU interfaces
+	 *           specified in CPUTargetList field)
+	 * [23:16] = core mask lsb[7:0] (forward interrupt to target cpu)
+	 * [15]    = 0 (forward SGI only if it is configured as group 0 interrupt)
+	 * [3:0]   = 0xF (interrupt ID = 15)
+	 */
+	lsl	w1, w3, #16
+	orr	w1, w1, #0xF
+	str	w1, [x4, #GICD_SGIR_OFFSET]
+	dsb	sy
+	isb
+
+	/* load '0' on success */
+	mov	x0, xzr
+
+	mov	x30, x5
+	ret
+endfunc _soc_core_restart
+
+/*
+ * This function determines if a core is disabled via COREDISR
+ * in:  w0  = core_mask_lsb
+ * out: w0  = 0, core not disabled
+ *      w0 != 0, core disabled
+ * uses x0, x1, x2
+ */
+func _soc_ck_disabled
+	/* get base addr of dcfg block */
+	mov	x1, #NXP_DCFG_ADDR
+
+	/* read COREDISR */
+	ldr	w1, [x1, #DCFG_COREDISR_OFFSET]
+	rev	w2, w1
+
+	/* test core bit */
+	and	w0, w2, w0
+	ret
+endfunc _soc_ck_disabled
+
+/*
+ *This function resets the system via SoC-specific methods
+ * in:  none
+ * out: none
+ * uses x0, x1, x2, x3
+ */
+func _soc_sys_reset
+	ldr	x2, =NXP_DCFG_ADDR
+
+	/* make sure the mask is cleared in the reset request mask register */
+	mov	w1, wzr
+	str	w1, [x2, #DCFG_RSTRQMR1_OFFSET]
+
+	/* set the reset request */
+	ldr	w1, =RSTCR_RESET_REQ
+	ldr	x3, =DCFG_RSTCR_OFFSET
+	rev	w0, w1
+	str	w0, [x2, x3]
+
+	/*
+	 * just in case this address range is mapped as cacheable,
+	 * flush the write out of the dcaches
+	 */
+	add	x3, x2, x3
+	dc	cvac, x3
+	dsb	st
+	isb
+
+	/* Note: this function does not return */
+1:
+	wfi
+	b	1b
+endfunc _soc_sys_reset
+
+/*
+ * Part of SYSTEM_OFF
+ * this function turns off the SoC clocks
+ * Note: this function is not intended to return, and the only allowable
+ *       recovery is POR
+ * in:  none
+ * out: none
+ * uses x0, x1, x2, x3, x4, x5, x6, x7, x8, x9
+ */
+func _soc_sys_off
+
+	/* mask interrupts at the core */
+	mrs	x1, DAIF
+	mov	x0, #DAIF_SET_MASK
+	orr	x0, x1, x0
+	msr	DAIF, x0
+
+	/* disable icache, dcache, mmu @ EL1 */
+	mov	x1, #SCTLR_I_C_M_MASK
+	mrs	x0, sctlr_el1
+	bic	x0, x0, x1
+	msr	sctlr_el1, x0
+
+	/* disable dcache for EL3 */
+	mrs	x1, SCTLR_EL3
+	bic	x1, x1, #SCTLR_C_MASK
+	/* make sure icache is enabled */
+	orr	x1, x1, #SCTLR_I_MASK
+	msr	SCTLR_EL3, x1
+	isb
+
+	/* Enable dynamic retention ctrl (CPUECTLR[2:0]) and SMP (CPUECTLR[6]) */
+	mrs	x0, CORTEX_A72_ECTLR_EL1
+	orr	x0, x0, #CPUECTLR_TIMER_8TICKS
+	orr	x0, x0, #CPUECTLR_SMPEN_EN
+	msr	CORTEX_A72_ECTLR_EL1, x0
+
+	/* set WFIL2EN in SCFG_CLUSTERPMCR */
+	ldr	x0, =SCFG_COREPMCR_OFFSET
+	ldr	x1, =COREPMCR_WFIL2
+	bl	write_reg_scfg
+
+	/* request LPM20 */
+	mov	x0, #RCPM_POWMGTCSR_OFFSET
+	bl	read_reg_rcpm
+	orr	x1, x0, #RCPM_POWMGTCSR_LPM20_REQ
+	mov	x0, #RCPM_POWMGTCSR_OFFSET
+	bl	write_reg_rcpm
+
+	dsb  sy
+	isb
+1:
+	wfi
+	b	1b
+endfunc _soc_sys_off
+
+/*
+ * Write a register in the RCPM block
+ * in:  x0 = offset
+ * in:  w1 = value to write
+ * uses x0, x1, x2, x3
+ */
+func write_reg_rcpm
+	ldr	x2, =NXP_RCPM_ADDR
+	/* swap for BE */
+	rev	w3, w1
+	str	w3, [x2, x0]
+	ret
+endfunc write_reg_rcpm
+
+/*
+ * Read a register in the RCPM block
+ * in:  x0 = offset
+ * out: w0 = value read
+ * uses x0, x1, x2
+ */
+func read_reg_rcpm
+	ldr	x2, =NXP_RCPM_ADDR
+	ldr	w1, [x2, x0]
+	/* swap for BE */
+	rev	w0, w1
+	ret
+endfunc read_reg_rcpm
+
+/*
+ * Write a register in the SCFG block
+ * in:  x0 = offset
+ * in:  w1 = value to write
+ * uses x0, x1, x2, x3
+ */
+func write_reg_scfg
+	mov	x2, #NXP_SCFG_ADDR
+	/* swap for BE */
+	rev	w3, w1
+	str	w3, [x2, x0]
+	ret
+endfunc write_reg_scfg
+
+/*
+ * Read a register in the SCFG block
+ * in:  x0 = offset
+ * out: w0 = value read
+ * uses x0, x1, x2
+ */
+func read_reg_scfg
+	mov	x2, #NXP_SCFG_ADDR
+	ldr	w1, [x2, x0]
+	/* swap for BE */
+	rev	w0, w1
+	ret
+endfunc read_reg_scfg
+
+/*
+ * Part of CPU_OFF
+ * this function programs SoC & GIC registers in preparation for shutting down
+ * the core
+ * in:  x0 = core mask lsb
+ * out: none
+ * uses x0, x1, x2, x3, x4, x5, x6, x7
+ */
+func _soc_core_prep_off
+	mov	x7, x30
+	mov	x6, x0
+
+	/* Set retention control in CPUECTLR make sure smpen bit is set */
+	mrs	x4, CORTEX_A72_ECTLR_EL1
+	bic	x4, x4, #CPUECTLR_RET_MASK
+	orr	x4, x4, #CPUECTLR_TIMER_8TICKS
+	orr	x4, x4, #CPUECTLR_SMPEN_EN
+	msr	CORTEX_A72_ECTLR_EL1, x4
+
+	/* save timer control current value */
+	mov	x5, #NXP_TIMER_ADDR
+	ldr	w4, [x5, #SYS_COUNTER_CNTCR_OFFSET]
+	mov	w2, w4
+	mov	x0, x6
+	mov	x1, #TIMER_CNTRL_DATA
+	bl	_setCoreData
+
+	/* enable the timer */
+	orr	w4, w4, #CNTCR_EN_MASK
+	str	w4, [x5, #SYS_COUNTER_CNTCR_OFFSET]
+
+	bl	_getGICC_BaseAddr
+	mov	x5, x0
+
+	/* disable signaling of ints */
+	ldr	w3, [x5, #GICC_CTLR_OFFSET]
+	bic	w3, w3, #GICC_CTLR_EN_GRP0
+	bic	w3, w3, #GICC_CTLR_EN_GRP1
+	str	w3, [x5, #GICC_CTLR_OFFSET]
+	dsb	sy
+	isb
+
+
+	/*
+	 * set retention control in SCFG_RETREQCR
+	 * Note: this register is msb 0
+	 */
+	ldr	x4, =SCFG_RETREQCR_OFFSET
+	mov	x0, x4
+	bl	read_reg_scfg
+	rbit	w1, w6
+	orr	w1, w0, w1
+	mov	x0, x4
+	bl	write_reg_scfg
+
+	/* set the priority filter */
+	ldr	w2, [x5, #GICC_PMR_OFFSET]
+	orr	w2, w2, #GICC_PMR_FILTER
+	str	w2, [x5, #GICC_PMR_OFFSET]
+
+	/* setup GICC_CTLR */
+	bic	w3, w3, #GICC_CTLR_ACKCTL_MASK
+	orr	w3, w3, #GICC_CTLR_FIQ_EN_MASK
+	orr	w3, w3, #GICC_CTLR_EOImodeS_MASK
+	orr	w3, w3, #GICC_CTLR_CBPR_MASK
+	str	w3, [x5, #GICC_CTLR_OFFSET]
+
+	/* setup the banked-per-core GICD registers */
+	bl	_getGICD_BaseAddr
+	mov	x5, x0
+
+	/* define SGI15 as Grp0 */
+	ldr	w2, [x5, #GICD_IGROUPR0_OFFSET]
+	bic	w2, w2, #GICD_IGROUP0_SGI15
+	str	w2, [x5, #GICD_IGROUPR0_OFFSET]
+
+	/* set priority of SGI 15 to highest... */
+	ldr	w2, [x5, #GICD_IPRIORITYR3_OFFSET]
+	bic	w2, w2, #GICD_IPRIORITY_SGI15_MASK
+	str	w2, [x5, #GICD_IPRIORITYR3_OFFSET]
+
+	/* enable SGI 15 */
+	ldr	w2, [x5, #GICD_ISENABLER0_OFFSET]
+	orr	w2, w2, #GICD_ISENABLE0_SGI15
+	str	w2, [x5, #GICD_ISENABLER0_OFFSET]
+
+	/* enable the cpu interface */
+	bl	_getGICC_BaseAddr
+	mov	x2, x0
+	orr	w3, w3, #GICC_CTLR_EN_GRP0
+	str	w3, [x2, #GICC_CTLR_OFFSET]
+
+
+	/* clear any pending SGIs */
+	ldr	x2, =GICD_CPENDSGIR_CLR_MASK
+	add	x0, x5, #GICD_CPENDSGIR3_OFFSET
+	str	w2, [x0]
+
+	/*
+	 * Set the PC_PH20_REQ bit in RCPM_PCPH20SETR
+	 * this is an lsb-0 register
+	 */
+	mov	x1, x6
+	mov	x0, #RCPM_PCPH20SETR_OFFSET
+	bl	write_reg_rcpm
+
+	dsb	sy
+	isb
+	mov	x30, x7
+	ret
+endfunc _soc_core_prep_off
+
+/*
+ * Part of CPU_OFF
+ * this function performs the final steps to shutdown the core
+ * in:  x0 = core mask lsb
+ * out: none
+ * uses x0, x1, x2, x3, x4, x5
+ */
+func _soc_core_entr_off
+	mov	x5, x30
+	mov	x4, x0
+
+	bl	_getGICD_BaseAddr
+	mov	x3, x0
+
+3:
+	/* enter low-power state by executing wfi */
+	wfi
+
+	/* see if we got hit by SGI 15 */
+	add	x0, x3, #GICD_SPENDSGIR3_OFFSET
+	ldr	w2, [x0]
+	and	w2, w2, #GICD_SPENDSGIR3_SGI15_MASK
+	cbz	w2, 4f
+
+	/* clear the pending SGI */
+	ldr	x2, =GICD_CPENDSGIR_CLR_MASK
+	add	x0, x3, #GICD_CPENDSGIR3_OFFSET
+	str	w2, [x0]
+4:
+	/* check if core has been turned on */
+	mov	x0, x4
+	bl	_getCoreState
+
+	cmp	x0, #CORE_WAKEUP
+	b.ne	3b
+
+	/* if we get here, then we have exited the wfi */
+	dsb	sy
+	isb
+	mov	x30, x5
+	ret
+endfunc _soc_core_entr_off
+
+/*
+ * Part of CPU_OFF
+ * this function starts the process of starting a core back up
+ * in:  x0 = core mask lsb
+ * out: none
+ * uses x0, x1, x2, x3, x4, x5, x6
+ */
+func _soc_core_exit_off
+	mov	x6, x30
+	mov	x5, x0
+
+	/*
+	 * Clear ph20 request in RCPM_PCPH20CLRR - no need
+	 * to do that here, it has been done in _soc_core_restart
+	 */
+	bl	_getGICC_BaseAddr
+	mov	x1, x0
+
+	/* read GICC_IAR */
+	ldr	w0, [x1, #GICC_IAR_OFFSET]
+
+	/* write GICC_EIOR - signal end-of-interrupt */
+	str	w0, [x1, #GICC_EOIR_OFFSET]
+
+	/* write GICC_DIR - disable interrupt */
+	str	w0, [x1, #GICC_DIR_OFFSET]
+
+	/* disable signaling of grp0 ints */
+	ldr	w3, [x1, #GICC_CTLR_OFFSET]
+	bic	w3, w3, #GICC_CTLR_EN_GRP0
+	str	w3, [x1, #GICC_CTLR_OFFSET]
+
+	/*
+	 * Unset retention request in SCFG_RETREQCR
+	 * Note: this register is msb-0
+	 */
+	ldr	x4, =SCFG_RETREQCR_OFFSET
+	mov	x0, x4
+	bl	read_reg_scfg
+	rbit	w1, w5
+	bic	w1, w0, w1
+	mov	x0, x4
+	bl	write_reg_scfg
+
+	/* restore timer ctrl */
+	mov	x0, x5
+	mov	x1, #TIMER_CNTRL_DATA
+	bl	_getCoreData
+	/* w0 = timer ctrl saved value */
+	mov	x2, #NXP_TIMER_ADDR
+	str	w0, [x2, #SYS_COUNTER_CNTCR_OFFSET]
+
+	dsb	sy
+	isb
+	mov	x30, x6
+	ret
+endfunc _soc_core_exit_off
+
+/*
+ * Function loads a 64-bit execution address of the core in the soc registers
+ * BOOTLOCPTRL/H
+ * in:  x0, 64-bit address to write to BOOTLOCPTRL/H
+ * uses x0, x1, x2, x3
+ */
+func _soc_set_start_addr
+	/* get the 64-bit base address of the scfg block */
+	ldr	x2, =NXP_SCFG_ADDR
+
+	/* write the 32-bit BOOTLOCPTRL register */
+	mov	x1, x0
+	rev	w3, w1
+	str	w3, [x2, #SCFG_BOOTLOCPTRL_OFFSET]
+
+	/* write the 32-bit BOOTLOCPTRH register */
+	lsr	x1, x0, #32
+	rev	w3, w1
+	str	w3, [x2, #SCFG_BOOTLOCPTRH_OFFSET]
+	ret
+endfunc _soc_set_start_addr
+
+/*
+ * This function returns the base address of the gic distributor
+ * in:  none
+ * out: x0 = base address of gic distributor
+ * uses x0
+ */
+func _getGICD_BaseAddr
+#if (TEST_BL31)
+	/* defect in simulator - gic base addresses are on 4Kb boundary */
+	ldr	x0, =NXP_GICD_4K_ADDR
+#else
+	ldr	x0, =NXP_GICD_64K_ADDR
+#endif
+	ret
+endfunc _getGICD_BaseAddr
+
+/*
+ * This function returns the base address of the gic controller
+ * in:  none
+ * out: x0 = base address of gic controller
+ * uses x0
+ */
+func _getGICC_BaseAddr
+#if (TEST_BL31)
+	/* defect in simulator - gic base addresses are on 4Kb boundary */
+	ldr	x0, =NXP_GICC_4K_ADDR
+#else
+	ldr	x0, =NXP_GICC_64K_ADDR
+#endif
+	ret
+endfunc _getGICC_BaseAddr
+
+/*
+ * Part of CPU_SUSPEND
+ * this function puts the calling core into standby state
+ * in:  x0 = core mask lsb
+ * out: none
+ * uses x0
+ */
+func _soc_core_entr_stdby
+	dsb	sy
+	isb
+	wfi
+
+	ret
+endfunc _soc_core_entr_stdby
+
+
+/*
+ * Part of CPU_SUSPEND
+ * this function performs SoC-specific programming prior to standby
+ * in:  x0 = core mask lsb
+ * out: none
+ * uses x0, x1
+ */
+func _soc_core_prep_stdby
+	/* clear CORTEX_A72_ECTLR_EL1[2:0] */
+	mrs	x1, CORTEX_A72_ECTLR_EL1
+	bic	x1, x1, #CPUECTLR_TIMER_MASK
+	msr	CORTEX_A72_ECTLR_EL1, x1
+
+	ret
+endfunc _soc_core_prep_stdby
+
+/*
+ * Part of CPU_SUSPEND
+ * this function performs any SoC-specific cleanup after standby state
+ * in:  x0 = core mask lsb
+ * out: none
+ * uses none
+ */
+func _soc_core_exit_stdby
+	ret
+endfunc _soc_core_exit_stdby
+
+/*
+ * Part of CPU_SUSPEND
+ * this function performs SoC-specific programming prior to power-down
+ * in:  x0 = core mask lsb
+ * out: none
+ * uses x0, x1, x2, x3, x4, x5
+ */
+func _soc_core_prep_pwrdn
+	mov	x5, x30
+	mov	x4, x0
+
+	/* enable CPU retention + set smp */
+	mrs	x1, CORTEX_A72_ECTLR_EL1
+	orr	x1, x1, #0x1
+	orr	x1, x1, #CPUECTLR_SMPEN_MASK
+	msr	CORTEX_A72_ECTLR_EL1, x1
+
+	/*
+	 * set the retention request in SCFG_RETREQCR
+	 * this is an msb-0 register
+	 */
+	ldr	x3, =SCFG_RETREQCR_OFFSET
+	mov	x0, x3
+	bl	read_reg_scfg
+	rbit	w1, w4
+	orr	w1, w0, w1
+	mov	x0, x3
+	bl	write_reg_scfg
+
+	/*
+	 * Set the PC_PH20_REQ bit in RCPM_PCPH20SETR
+	 * this is an lsb-0 register
+	 */
+	mov	x1, x4
+	mov	x0, #RCPM_PCPH20SETR_OFFSET
+	bl	write_reg_rcpm
+
+	mov	x30, x5
+	ret
+endfunc _soc_core_prep_pwrdn
+
+/*
+ * Part of CPU_SUSPEND
+ * this function puts the calling core into a power-down state
+ * in:  x0 = core mask lsb
+ * out: none
+ * uses x0
+ */
+func _soc_core_entr_pwrdn
+	dsb	sy
+	isb
+	wfi
+
+	ret
+endfunc _soc_core_entr_pwrdn
+
+/*
+ * Part of CPU_SUSPEND
+ * this function cleans up after a core exits power-down
+ * in:  x0 = core mask lsb
+ * out: none
+ * uses x0, x1, x2, x3, x4, x5
+ */
+func _soc_core_exit_pwrdn
+	mov	x5, x30
+	mov	x4, x0
+
+	/*
+	 * Set the PC_PH20_REQ bit in RCPM_PCPH20CLRR
+	 * this is an lsb-0 register
+	 */
+	mov	x1, x4
+	mov	x0, #RCPM_PCPH20CLRR_OFFSET
+	bl	write_reg_rcpm
+
+	/*
+	 * Unset the retention request in SCFG_RETREQCR
+	 * this is an msb-0 register
+	 */
+	ldr	x3, =SCFG_RETREQCR_OFFSET
+	mov	x0, x3
+	bl	read_reg_scfg
+	rbit	w1, w4
+	bic	w1, w0, w1
+	mov	x0, x3
+	bl	write_reg_scfg
+
+	mov	x30, x5
+	ret
+endfunc _soc_core_exit_pwrdn
+
+/*
+ * Part of CPU_SUSPEND
+ * this function performs SoC-specific programming prior to standby
+ * in:  x0 = core mask lsb
+ * out: none
+ * uses none
+ */
+func _soc_clstr_prep_stdby
+	/* clear CORTEX_A72_ECTLR_EL1[2:0] */
+	mrs	x1, CORTEX_A72_ECTLR_EL1
+	bic	x1, x1, #CPUECTLR_TIMER_MASK
+	msr	CORTEX_A72_ECTLR_EL1, x1
+
+	ret
+endfunc _soc_clstr_prep_stdby
+
+/*
+ * Part of CPU_SUSPEND
+ * this function performs any SoC-specific cleanup after standby state
+ * in:  x0 = core mask lsb
+ * out: none
+ * uses none
+ */
+func _soc_clstr_exit_stdby
+	ret
+endfunc _soc_clstr_exit_stdby
+
+/*
+ * Part of CPU_SUSPEND
+ * this function performs SoC-specific programming prior to power-down
+ * in:  x0 = core mask lsb
+ * out: none
+ * uses x0, x1, x2, x3, x4, x5
+ */
+func _soc_clstr_prep_pwrdn
+	mov	x5, x30
+	mov	x4, x0
+
+	/* enable CPU retention + set smp */
+	mrs	x1, CORTEX_A72_ECTLR_EL1
+	orr	x1, x1, #0x1
+	orr	x1, x1, #CPUECTLR_SMPEN_MASK
+	msr	CORTEX_A72_ECTLR_EL1, x1
+
+	/*
+	 * Set the retention request in SCFG_RETREQCR
+	 * this is an msb-0 register.
+	 */
+	ldr	x3, =SCFG_RETREQCR_OFFSET
+	mov	x0, x3
+	bl	read_reg_scfg
+	rbit	w1, w4
+	orr	w1, w0, w1
+	mov	x0, x3
+	bl	write_reg_scfg
+
+	/*
+	 * Set the PC_PH20_REQ bit in RCPM_PCPH20SETR
+	 * this is an lsb-0 register.
+	 */
+	mov	x1, x4
+	mov	x0, #RCPM_PCPH20SETR_OFFSET
+	bl	write_reg_rcpm
+
+	mov	x30, x5
+	ret
+endfunc _soc_clstr_prep_pwrdn
+
+/*
+ * Part of CPU_SUSPEND
+ * this function cleans up after a core exits power-down
+ * in:  x0 = core mask lsb
+ * out: none
+ * uses x0, x1, x2, x3, x4, x5
+ */
+func _soc_clstr_exit_pwrdn
+	mov	x5, x30
+	mov	x4, x0
+
+	/*
+	 * Set the PC_PH20_REQ bit in RCPM_PCPH20CLRR
+	 * this is an lsb-0 register.
+	 */
+	mov	x1, x4
+	mov	x0, #RCPM_PCPH20CLRR_OFFSET
+	bl	write_reg_rcpm
+
+	/*
+	 * Unset the retention request in SCFG_RETREQCR
+	 * this is an msb-0 register.
+	 */
+	ldr	x3, =SCFG_RETREQCR_OFFSET
+	mov	x0, x3
+	bl	read_reg_scfg
+	rbit	w1, w4
+	bic	w1, w0, w1
+	mov	x0, x3
+	bl	write_reg_scfg
+
+	mov	x30, x5
+	ret
+endfunc _soc_clstr_exit_pwrdn
+
+/*
+ * Part of CPU_SUSPEND
+ * this function performs SoC-specific programming prior to standby
+ * in:  x0 = core mask lsb
+ * out: none
+ * uses none
+ */
+func _soc_sys_prep_stdby
+	/* clear CORTEX_A72_ECTLR_EL1[2:0] */
+	mrs	x1, CORTEX_A72_ECTLR_EL1
+	bic	x1, x1, #CPUECTLR_TIMER_MASK
+	msr	CORTEX_A72_ECTLR_EL1, x1
+
+	ret
+endfunc _soc_sys_prep_stdby
+
+/* Part of CPU_SUSPEND
+ * this function performs any SoC-specific cleanup after standby state
+ * in:  x0 = core mask lsb
+ * out: none
+ * uses none
+ */
+func _soc_sys_exit_stdby
+	ret
+endfunc _soc_sys_exit_stdby
+
+/*
+ * Part of CPU_SUSPEND
+ * this function performs SoC-specific programming prior to
+ * suspend-to-power-down
+ * in:  x0 = core mask lsb
+ * out: none
+ * uses x0, x1, x2, x3, x4
+ */
+func _soc_sys_prep_pwrdn
+	mov	x4, x30
+
+	/* Enable dynamic retention contrl (CPUECTLR[2:0]) and SMP (CPUECTLR[6]) */
+	mrs	x0, CORTEX_A72_ECTLR_EL1
+	bic	x0, x0, #CPUECTLR_TIMER_MASK
+	orr	x0, x0, #CPUECTLR_TIMER_8TICKS
+	orr	x0, x0, #CPUECTLR_SMPEN_EN
+	msr	CORTEX_A72_ECTLR_EL1, x0
+
+	/* Set WFIL2EN in SCFG_CLUSTERPMCR */
+	ldr	x0, =SCFG_COREPMCR_OFFSET
+	ldr	x1, =COREPMCR_WFIL2
+	bl	write_reg_scfg
+
+	isb
+	mov	x30, x4
+	ret
+endfunc _soc_sys_prep_pwrdn
+
+/*
+ * Part of CPU_SUSPEND
+ * this function puts the calling core, and potentially the soc, into a
+ * low-power state
+ * in:  x0 = core mask lsb
+ * out: x0 = 0, success
+ *      x0 < 0, failure
+ * uses x0, x1, x2, x3, x4
+ */
+func _soc_sys_pwrdn_wfi
+	mov	x4, x30
+
+	/* request LPM20 */
+	mov	x0, #RCPM_POWMGTCSR_OFFSET
+	bl	read_reg_rcpm
+	orr	x1, x0, #RCPM_POWMGTCSR_LPM20_REQ
+	mov	x0, #RCPM_POWMGTCSR_OFFSET
+	bl	write_reg_rcpm
+
+	dsb	sy
+	isb
+	wfi
+
+	mov	x30, x4
+	ret
+endfunc _soc_sys_pwrdn_wfi
+
+/*
+ * Part of CPU_SUSPEND
+ * this function performs any SoC-specific cleanup after power-down
+ * in:  x0 = core mask lsb
+ * out: none
+ * uses x0, x1
+ */
+func _soc_sys_exit_pwrdn
+	/* clear WFIL2_EN in SCFG_COREPMCR */
+	mov	x1, #NXP_SCFG_ADDR
+	str	wzr, [x1, #SCFG_COREPMCR_OFFSET]
+
+	ret
+endfunc _soc_sys_exit_pwrdn
diff --git a/plat/nxp/soc-ls1046a/aarch64/ls1046a_helpers.S b/plat/nxp/soc-ls1046a/aarch64/ls1046a_helpers.S
new file mode 100644
index 0000000..d2a48ea
--- /dev/null
+++ b/plat/nxp/soc-ls1046a/aarch64/ls1046a_helpers.S
@@ -0,0 +1,92 @@
+/*
+ * Copyright 2018-2022 NXP
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ *
+ */
+
+#include <arch.h>
+#include <asm_macros.S>
+
+#include <platform_def.h>
+
+	.globl	plat_secondary_cold_boot_setup
+	.globl	plat_is_my_cpu_primary
+	.globl	plat_reset_handler
+	.globl  platform_mem_init
+
+func platform_mem1_init
+	ret
+endfunc platform_mem1_init
+
+func platform_mem_init
+	ret
+endfunc	platform_mem_init
+
+func l2_mem_init
+	/* Initialize the L2 RAM latency */
+	mrs	x1, S3_1_c11_c0_2
+	mov	x0, #0x1C7
+	/* Clear L2 Tag RAM latency and L2 Data RAM latency */
+	bic	x1, x1, x0
+	/* Set L2 data ram latency bits [2:0] */
+	orr	x1, x1, #0x2
+	/* set L2 tag ram latency bits [8:6] */
+	orr	x1,  x1, #0x80
+	msr	S3_1_c11_c0_2, x1
+	isb
+	ret
+endfunc	l2_mem_init
+
+func apply_platform_errata
+	ret
+endfunc apply_platform_errata
+
+func plat_reset_handler
+	mov	x29, x30
+#if (defined(IMAGE_BL2) && BL2_AT_EL3)
+	bl	l2_mem_init
+#endif
+	bl	apply_platform_errata
+
+#if defined(IMAGE_BL31)
+	ldr	x0, =POLICY_SMMU_PAGESZ_64K
+	cbz	x0, 1f
+	/* Set the SMMU page size in the SACR register */
+	bl	_set_smmu_pagesz_64
+#endif
+1:
+	/*
+	 * May be cntfrq_el0 needs to be assigned
+	 * the value COUNTER_FREQUENCY
+	 */
+	mov	x30, x29
+	ret
+endfunc plat_reset_handler
+
+/*
+ * void plat_secondary_cold_boot_setup (void);
+ *
+ * This function performs any platform specific actions
+ * needed for a secondary cpu after a cold reset e.g
+ * mark the cpu's presence, mechanism to place it in a
+ * holding pen etc.
+ */
+func plat_secondary_cold_boot_setup
+	/* ls1046a does not do cold boot for secondary CPU */
+cb_panic:
+	b	cb_panic
+endfunc plat_secondary_cold_boot_setup
+
+/*
+ * unsigned int plat_is_my_cpu_primary (void);
+ *
+ * Find out whether the current cpu is the primary cpu.
+ */
+func plat_is_my_cpu_primary
+	mrs	x0, mpidr_el1
+	and	x0, x0, #(MPIDR_CLUSTER_MASK | MPIDR_CPU_MASK)
+	cmp	x0, 0x0
+	cset	w0, eq
+	ret
+endfunc plat_is_my_cpu_primary
diff --git a/plat/nxp/soc-ls1046a/include/ns_access.h b/plat/nxp/soc-ls1046a/include/ns_access.h
new file mode 100644
index 0000000..25c1964
--- /dev/null
+++ b/plat/nxp/soc-ls1046a/include/ns_access.h
@@ -0,0 +1,174 @@
+/*
+ * Copyright 2017-2018, 2020-2022 NXP
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#ifndef NS_ACCESS_H
+#define NS_ACCESS_H
+
+#include <csu.h>
+
+enum csu_cslx_ind {
+	CSU_CSLX_PCIE2_IO = 0,
+	CSU_CSLX_PCIE1_IO,
+	CSU_CSLX_MG2TPR_IP,
+	CSU_CSLX_IFC_MEM,
+	CSU_CSLX_OCRAM,
+	CSU_CSLX_GIC,
+	CSU_CSLX_PCIE1,
+	CSU_CSLX_OCRAM2,
+	CSU_CSLX_QSPI_MEM,
+	CSU_CSLX_PCIE2,
+	CSU_CSLX_SATA,
+	CSU_CSLX_USB1,
+	CSU_CSLX_QM_BM_SWPORTAL,
+	CSU_CSLX_PCIE3 = 16,
+	CSU_CSLX_PCIE3_IO,
+	CSU_CSLX_USB3 = 20,
+	CSU_CSLX_USB2,
+	CSU_CSLX_PFE = 23,
+	CSU_CSLX_SERDES = 32,
+	CSU_CSLX_QDMA,
+	CSU_CSLX_LPUART2,
+	CSU_CSLX_LPUART1,
+	CSU_CSLX_LPUART4,
+	CSU_CSLX_LPUART3,
+	CSU_CSLX_LPUART6,
+	CSU_CSLX_LPUART5,
+	CSU_CSLX_DSPI1 = 41,
+	CSU_CSLX_QSPI,
+	CSU_CSLX_ESDHC,
+	CSU_CSLX_IFC = 45,
+	CSU_CSLX_I2C1,
+	CSU_CSLX_USB_2,
+	CSU_CSLX_I2C3 = 48,
+	CSU_CSLX_I2C2,
+	CSU_CSLX_DUART2 = 50,
+	CSU_CSLX_DUART1,
+	CSU_CSLX_WDT2,
+	CSU_CSLX_WDT1,
+	CSU_CSLX_EDMA,
+	CSU_CSLX_SYS_CNT,
+	CSU_CSLX_DMA_MUX2,
+	CSU_CSLX_DMA_MUX1,
+	CSU_CSLX_DDR,
+	CSU_CSLX_QUICC,
+	CSU_CSLX_DCFG_CCU_RCPM = 60,
+	CSU_CSLX_SECURE_BOOTROM,
+	CSU_CSLX_SFP,
+	CSU_CSLX_TMU,
+	CSU_CSLX_SECURE_MONITOR,
+	CSU_CSLX_SCFG,
+	CSU_CSLX_FM = 66,
+	CSU_CSLX_SEC5_5,
+	CSU_CSLX_BM,
+	CSU_CSLX_QM,
+	CSU_CSLX_GPIO2 = 70,
+	CSU_CSLX_GPIO1,
+	CSU_CSLX_GPIO4,
+	CSU_CSLX_GPIO3,
+	CSU_CSLX_PLATFORM_CONT,
+	CSU_CSLX_CSU,
+	CSU_CSLX_IIC4 = 77,
+	CSU_CSLX_WDT4,
+	CSU_CSLX_WDT3,
+	CSU_CSLX_ESDHC2 = 80,
+	CSU_CSLX_WDT5 = 81,
+	CSU_CSLX_SAI2,
+	CSU_CSLX_SAI1,
+	CSU_CSLX_SAI4,
+	CSU_CSLX_SAI3,
+	CSU_CSLX_FTM2 = 86,
+	CSU_CSLX_FTM1,
+	CSU_CSLX_FTM4,
+	CSU_CSLX_FTM3,
+	CSU_CSLX_FTM6 = 90,
+	CSU_CSLX_FTM5,
+	CSU_CSLX_FTM8,
+	CSU_CSLX_FTM7,
+	CSU_CSLX_DSCR = 121,
+};
+
+struct csu_ns_dev_st ns_dev[] = {
+	 {CSU_CSLX_PCIE2_IO, CSU_ALL_RW},
+	 {CSU_CSLX_PCIE1_IO, CSU_ALL_RW},
+	 {CSU_CSLX_MG2TPR_IP, CSU_ALL_RW},
+	 {CSU_CSLX_IFC_MEM, CSU_ALL_RW},
+	 {CSU_CSLX_OCRAM, CSU_S_SUP_RW},
+	 {CSU_CSLX_GIC, CSU_ALL_RW},
+	 {CSU_CSLX_PCIE1, CSU_ALL_RW},
+	 {CSU_CSLX_OCRAM2, CSU_S_SUP_RW},
+	 {CSU_CSLX_QSPI_MEM, CSU_ALL_RW},
+	 {CSU_CSLX_PCIE2, CSU_ALL_RW},
+	 {CSU_CSLX_SATA, CSU_ALL_RW},
+	 {CSU_CSLX_USB1, CSU_ALL_RW},
+	 {CSU_CSLX_QM_BM_SWPORTAL, CSU_ALL_RW},
+	 {CSU_CSLX_PCIE3, CSU_ALL_RW},
+	 {CSU_CSLX_PCIE3_IO, CSU_ALL_RW},
+	 {CSU_CSLX_USB3, CSU_ALL_RW},
+	 {CSU_CSLX_USB2, CSU_ALL_RW},
+	 {CSU_CSLX_PFE, CSU_ALL_RW},
+	 {CSU_CSLX_SERDES, CSU_ALL_RW},
+	 {CSU_CSLX_QDMA, CSU_ALL_RW},
+	 {CSU_CSLX_LPUART2, CSU_ALL_RW},
+	 {CSU_CSLX_LPUART1, CSU_ALL_RW},
+	 {CSU_CSLX_LPUART4, CSU_ALL_RW},
+	 {CSU_CSLX_LPUART3, CSU_ALL_RW},
+	 {CSU_CSLX_LPUART6, CSU_ALL_RW},
+	 {CSU_CSLX_LPUART5, CSU_ALL_RW},
+	 {CSU_CSLX_DSPI1, CSU_ALL_RW},
+	 {CSU_CSLX_QSPI, CSU_ALL_RW},
+	 {CSU_CSLX_ESDHC, CSU_ALL_RW},
+	 {CSU_CSLX_IFC, CSU_ALL_RW},
+	 {CSU_CSLX_I2C1, CSU_ALL_RW},
+	 {CSU_CSLX_USB_2, CSU_ALL_RW},
+	 {CSU_CSLX_I2C3, CSU_ALL_RW},
+	 {CSU_CSLX_I2C2, CSU_ALL_RW},
+	 {CSU_CSLX_DUART2, CSU_ALL_RW},
+	 {CSU_CSLX_DUART1, CSU_ALL_RW},
+	 {CSU_CSLX_WDT2, CSU_ALL_RW},
+	 {CSU_CSLX_WDT1, CSU_ALL_RW},
+	 {CSU_CSLX_EDMA, CSU_ALL_RW},
+	 {CSU_CSLX_SYS_CNT, CSU_ALL_RW},
+	 {CSU_CSLX_DMA_MUX2, CSU_ALL_RW},
+	 {CSU_CSLX_DMA_MUX1, CSU_ALL_RW},
+	 {CSU_CSLX_DDR, CSU_ALL_RW},
+	 {CSU_CSLX_QUICC, CSU_ALL_RW},
+	 {CSU_CSLX_DCFG_CCU_RCPM, CSU_ALL_RW},
+	 {CSU_CSLX_SECURE_BOOTROM, CSU_ALL_RW},
+	 {CSU_CSLX_SFP, CSU_ALL_RW},
+	 {CSU_CSLX_TMU, CSU_ALL_RW},
+	 {CSU_CSLX_SECURE_MONITOR, CSU_ALL_RW},
+	 {CSU_CSLX_SCFG, CSU_ALL_RW},
+	 {CSU_CSLX_FM, CSU_ALL_RW},
+	 {CSU_CSLX_SEC5_5, CSU_ALL_RW},
+	 {CSU_CSLX_BM, CSU_ALL_RW},
+	 {CSU_CSLX_QM, CSU_ALL_RW},
+	 {CSU_CSLX_GPIO2, CSU_ALL_RW},
+	 {CSU_CSLX_GPIO1, CSU_ALL_RW},
+	 {CSU_CSLX_GPIO4, CSU_ALL_RW},
+	 {CSU_CSLX_GPIO3, CSU_ALL_RW},
+	 {CSU_CSLX_PLATFORM_CONT, CSU_ALL_RW},
+	 {CSU_CSLX_CSU, CSU_ALL_RW},
+	 {CSU_CSLX_IIC4, CSU_ALL_RW},
+	 {CSU_CSLX_WDT4, CSU_ALL_RW},
+	 {CSU_CSLX_WDT3, CSU_ALL_RW},
+	 {CSU_CSLX_ESDHC2, CSU_ALL_RW},
+	 {CSU_CSLX_WDT5, CSU_ALL_RW},
+	 {CSU_CSLX_SAI2, CSU_ALL_RW},
+	 {CSU_CSLX_SAI1, CSU_ALL_RW},
+	 {CSU_CSLX_SAI4, CSU_ALL_RW},
+	 {CSU_CSLX_SAI3, CSU_ALL_RW},
+	 {CSU_CSLX_FTM2, CSU_ALL_RW},
+	 {CSU_CSLX_FTM1, CSU_ALL_RW},
+	 {CSU_CSLX_FTM4, CSU_ALL_RW},
+	 {CSU_CSLX_FTM3, CSU_ALL_RW},
+	 {CSU_CSLX_FTM6, CSU_ALL_RW},
+	 {CSU_CSLX_FTM5, CSU_ALL_RW},
+	 {CSU_CSLX_FTM8, CSU_ALL_RW},
+	 {CSU_CSLX_FTM7, CSU_ALL_RW},
+	 {CSU_CSLX_DSCR, CSU_ALL_RW},
+};
+
+#endif /* NS_ACCESS_H */
diff --git a/plat/nxp/soc-ls1046a/include/soc.h b/plat/nxp/soc-ls1046a/include/soc.h
new file mode 100644
index 0000000..67810c3
--- /dev/null
+++ b/plat/nxp/soc-ls1046a/include/soc.h
@@ -0,0 +1,125 @@
+/*
+ * Copyright 2018-2022 NXP
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ *
+ */
+
+#ifndef SOC_H
+#define	SOC_H
+
+/* Chassis specific defines - common across SoC's of a particular platform */
+#include <dcfg_lsch2.h>
+
+#include <soc_default_base_addr.h>
+#include <soc_default_helper_macros.h>
+
+/* DDR Regions Info */
+#define NUM_DRAM_REGIONS		U(3)
+#define	NXP_DRAM0_ADDR			ULL(0x80000000)
+#define NXP_DRAM0_MAX_SIZE		ULL(0x80000000)	/*  2 GB  */
+
+#define	NXP_DRAM1_ADDR			ULL(0x880000000)
+#define NXP_DRAM1_MAX_SIZE		ULL(0x780000000)	/* 30 GB  */
+
+#define	NXP_DRAM2_ADDR			ULL(0x8800000000)
+#define NXP_DRAM2_MAX_SIZE		ULL(0x7800000000)	/* 480 GB */
+
+/*DRAM0 Size defined in platform_def.h */
+#define	NXP_DRAM0_SIZE			PLAT_DEF_DRAM0_SIZE
+
+/*
+ * SVR Definition (not include major and minor rev)
+ * A: without security
+ * AE: with security
+ */
+#define SVR_LS1026A			0x870709
+#define SVR_LS1026AE			0x870708
+#define SVR_LS1046A			0x870701
+#define SVR_LS1046AE			0x870700
+
+/* Number of cores in platform */
+/* Used by common code for array initialization */
+#define NUMBER_OF_CLUSTERS		U(1)
+#define CORES_PER_CLUSTER		U(4)
+#define PLATFORM_CORE_COUNT		(NUMBER_OF_CLUSTERS * CORES_PER_CLUSTER)
+
+/*
+ * Required LS standard platform porting definitions
+ * for CCI-400
+ */
+#define NXP_CCI_CLUSTER0_SL_IFACE_IX	4
+
+
+/* Defines required for using XLAT tables from ARM common code */
+#define PLAT_PHY_ADDR_SPACE_SIZE	(1ULL << 40)
+#define PLAT_VIRT_ADDR_SPACE_SIZE	(1ULL << 40)
+
+/* Clock Divisors */
+#define NXP_PLATFORM_CLK_DIVIDER	U(1)
+#define NXP_UART_CLK_DIVIDER		U(2)
+
+/* set to 0 if the clusters are not symmetrical */
+#define SYMMETRICAL_CLUSTERS		U(1)
+
+ /*
+  * set this switch to 1 if you need to keep the debug block
+  * clocked during system power-down
+  */
+#define DEBUG_ACTIVE			0
+
+ /*
+  * pwr mgmt features supported in the soc-specific code:
+  *   value == 0x0  the soc code does not support this feature
+  *   value != 0x0  the soc code supports this feature
+  */
+#define SOC_CORE_RELEASE		0x1
+#define SOC_CORE_RESTART		0x1
+#define SOC_CORE_OFF			0x1
+#define SOC_CORE_STANDBY		0x1
+#define SOC_CORE_PWR_DWN		0x1
+#define SOC_CLUSTER_STANDBY		0x1
+#define SOC_CLUSTER_PWR_DWN		0x1
+#define SOC_SYSTEM_STANDBY		0x1
+#define SOC_SYSTEM_PWR_DWN		0x1
+#define SOC_SYSTEM_OFF			0x1
+#define SOC_SYSTEM_RESET		0x1
+
+/* Start: Macros used by lib/psci files */
+#define SYSTEM_PWR_DOMAINS		1
+#define PLAT_NUM_PWR_DOMAINS		(PLATFORM_CORE_COUNT + \
+					NUMBER_OF_CLUSTERS  + \
+					SYSTEM_PWR_DOMAINS)
+
+/* Power state coordination occurs at the system level */
+#define PLAT_MAX_PWR_LVL		MPIDR_AFFLVL2
+
+/* define retention state */
+#define PLAT_MAX_RET_STATE		(PSCI_LOCAL_STATE_RUN + 1)
+
+/* define power-down state */
+#define PLAT_MAX_OFF_STATE		(PLAT_MAX_RET_STATE + 1)
+
+/*
+ * Some data must be aligned on the biggest cache line size in the platform.
+ * This is known only to the platform as it might have a combination of
+ * integrated and external caches.
+ *
+ * CACHE_WRITEBACK_GRANULE is defined in soc.def
+ */
+
+ /* One cache line needed for bakery locks on ARM platforms */
+#define PLAT_PERCPU_BAKERY_LOCK_SIZE	(1 * CACHE_WRITEBACK_GRANULE)
+
+#ifndef __ASSEMBLER__
+/* CCI slave interfaces */
+static const int cci_map[] = {
+	NXP_CCI_CLUSTER0_SL_IFACE_IX,
+};
+
+void soc_init_lowlevel(void);
+void soc_init_percpu(void);
+void _soc_set_start_addr(unsigned long addr);
+#endif
+
+#endif /* SOC_H */
diff --git a/plat/nxp/soc-ls1046a/soc.c b/plat/nxp/soc-ls1046a/soc.c
new file mode 100644
index 0000000..d17e672
--- /dev/null
+++ b/plat/nxp/soc-ls1046a/soc.c
@@ -0,0 +1,395 @@
+/*
+ * Copyright 2018-2022 NXP
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#include <assert.h>
+
+#include <arch.h>
+#include <caam.h>
+#include <cassert.h>
+#include <cci.h>
+#include <common/debug.h>
+#include <dcfg.h>
+#ifdef I2C_INIT
+#include <i2c.h>
+#endif
+#include <lib/mmio.h>
+#include <lib/xlat_tables/xlat_tables_v2.h>
+#include <ls_interconnect.h>
+#ifdef POLICY_FUSE_PROVISION
+#include <nxp_gpio.h>
+#endif
+#if TRUSTED_BOARD_BOOT
+#include <nxp_smmu.h>
+#endif
+#include <nxp_timer.h>
+#include <plat_console.h>
+#include <plat_gic.h>
+#include <plat_tzc400.h>
+#include <scfg.h>
+#if defined(NXP_SFP_ENABLED)
+#include <sfp.h>
+#endif
+
+#include <errata.h>
+#include <ns_access.h>
+#ifdef CONFIG_OCRAM_ECC_EN
+#include <ocram.h>
+#endif
+#include <plat_common.h>
+#include <platform_def.h>
+#include <soc.h>
+
+static dcfg_init_info_t dcfg_init_data = {
+	.g_nxp_dcfg_addr = NXP_DCFG_ADDR,
+	.nxp_sysclk_freq = NXP_SYSCLK_FREQ,
+	.nxp_ddrclk_freq = NXP_DDRCLK_FREQ,
+	.nxp_plat_clk_divider = NXP_PLATFORM_CLK_DIVIDER,
+};
+
+/* Function to return the SoC SYS CLK  */
+static unsigned int get_sys_clk(void)
+{
+	return NXP_SYSCLK_FREQ;
+}
+
+/*
+ * Function returns the base counter frequency
+ * after reading the first entry at CNTFID0 (0x20 offset).
+ *
+ * Function is used by:
+ *   1. ARM common code for PSCI management.
+ *   2. ARM Generic Timer init.
+ *
+ */
+unsigned int plat_get_syscnt_freq2(void)
+{
+	unsigned int counter_base_frequency;
+
+	counter_base_frequency = get_sys_clk() / 4;
+
+	return counter_base_frequency;
+}
+
+#ifdef IMAGE_BL2
+/* Functions for BL2 */
+
+static struct soc_type soc_list[] =  {
+	SOC_ENTRY(LS1046A, LS1046A, 1, 4),
+	SOC_ENTRY(LS1046AE, LS1046AE, 1, 4),
+	SOC_ENTRY(LS1026A, LS1026A, 1, 2),
+	SOC_ENTRY(LS1026AE, LS1026AE, 1, 2),
+};
+
+#ifdef POLICY_FUSE_PROVISION
+static gpio_init_info_t gpio_init_data = {
+	.gpio1_base_addr = NXP_GPIO1_ADDR,
+	.gpio2_base_addr = NXP_GPIO2_ADDR,
+	.gpio3_base_addr = NXP_GPIO3_ADDR,
+	.gpio4_base_addr = NXP_GPIO4_ADDR,
+};
+#endif
+
+/*
+ * Function to set the base counter frequency at
+ * the first entry of the Frequency Mode Table,
+ * at CNTFID0 (0x20 offset).
+ *
+ * Set the value of the pirmary core register cntfrq_el0.
+ */
+static void set_base_freq_CNTFID0(void)
+{
+	/*
+	 * Below register specifies the base frequency of the system counter.
+	 * As per NXP Board Manuals:
+	 * The system counter always works with SYS_REF_CLK/4 frequency clock.
+	 */
+	unsigned int counter_base_frequency = get_sys_clk() / 4;
+
+	/* Setting the frequency in the Frequency modes table.
+	 *
+	 * Note: The value for ls1046ardb board at this offset
+	 *       is not RW as stated. This offset have the
+	 *       fixed value of 100000400 Hz.
+	 *
+	 * The below code line has no effect.
+	 * Keeping it for other platforms where it has effect.
+	 */
+	mmio_write_32(NXP_TIMER_ADDR + CNTFID_OFF, counter_base_frequency);
+
+	write_cntfrq_el0(counter_base_frequency);
+}
+
+void soc_preload_setup(void)
+{
+
+}
+
+/*
+ * This function implements soc specific erratas
+ * This is called before DDR is initialized or MMU is enabled
+ */
+void soc_early_init(void)
+{
+	uint8_t num_clusters, cores_per_cluster;
+	dram_regions_info_t *dram_regions_info = get_dram_regions_info();
+
+#ifdef CONFIG_OCRAM_ECC_EN
+	ocram_init(NXP_OCRAM_ADDR, NXP_OCRAM_SIZE);
+#endif
+	dcfg_init(&dcfg_init_data);
+#ifdef POLICY_FUSE_PROVISION
+	gpio_init(&gpio_init_data);
+	sec_init(NXP_CAAM_ADDR);
+#endif
+#if LOG_LEVEL > 0
+	/* Initialize the console to provide early debug support */
+
+	plat_console_init(NXP_CONSOLE_ADDR,
+				NXP_UART_CLK_DIVIDER, NXP_CONSOLE_BAUDRATE);
+#endif
+	set_base_freq_CNTFID0();
+
+	/* Enable snooping on SEC read and write transactions */
+	scfg_setbits32((void *)(NXP_SCFG_ADDR + SCFG_SNPCNFGCR_OFFSET),
+			SCFG_SNPCNFGCR_SECRDSNP | SCFG_SNPCNFGCR_SECWRSNP);
+
+	/*
+	 * Initialize Interconnect for this cluster during cold boot.
+	 * No need for locks as no other CPU is active.
+	 */
+	cci_init(NXP_CCI_ADDR, cci_map, ARRAY_SIZE(cci_map));
+
+	/*
+	 * Enable Interconnect coherency for the primary CPU's cluster.
+	 */
+	get_cluster_info(soc_list, ARRAY_SIZE(soc_list), &num_clusters, &cores_per_cluster);
+	plat_ls_interconnect_enter_coherency(num_clusters);
+
+#if TRUSTED_BOARD_BOOT
+	uint32_t mode;
+
+	sfp_init(NXP_SFP_ADDR);
+	/*
+	 * For secure boot disable SMMU.
+	 * Later when platform security policy comes in picture,
+	 * this might get modified based on the policy
+	 */
+	if (check_boot_mode_secure(&mode) == true) {
+		bypass_smmu(NXP_SMMU_ADDR);
+	}
+
+	/*
+	 * For Mbedtls currently crypto is not supported via CAAM
+	 * enable it when that support is there. In tbbr.mk
+	 * the CAAM_INTEG is set as 0.
+	 */
+#ifndef MBEDTLS_X509
+	/* Initialize the crypto accelerator if enabled */
+	if (is_sec_enabled() == false) {
+		INFO("SEC is disabled.\n");
+	} else {
+		sec_init(NXP_CAAM_ADDR);
+	}
+#endif
+#elif defined(POLICY_FUSE_PROVISION)
+	gpio_init(&gpio_init_data);
+	sfp_init(NXP_SFP_ADDR);
+	sec_init(NXP_CAAM_ADDR);
+#endif
+
+	soc_errata();
+
+	/* Initialize system level generic timer for Layerscape Socs. */
+	delay_timer_init(NXP_TIMER_ADDR);
+
+#ifdef DDR_INIT
+	i2c_init(NXP_I2C_ADDR);
+	dram_regions_info->total_dram_size = init_ddr();
+#endif
+}
+
+void soc_bl2_prepare_exit(void)
+{
+#if defined(NXP_SFP_ENABLED) && defined(DISABLE_FUSE_WRITE)
+	set_sfp_wr_disable();
+#endif
+}
+
+/* This function returns the boot device based on RCW_SRC */
+enum boot_device get_boot_dev(void)
+{
+	enum boot_device src = BOOT_DEVICE_NONE;
+	uint32_t porsr1;
+	uint32_t rcw_src, val;
+
+	porsr1 = read_reg_porsr1();
+
+	rcw_src = (porsr1 & PORSR1_RCW_MASK) >> PORSR1_RCW_SHIFT;
+
+	val = rcw_src & RCW_SRC_NAND_MASK;
+
+	if (val == RCW_SRC_NAND_VAL) {
+		val = rcw_src & NAND_RESERVED_MASK;
+		if ((val != NAND_RESERVED_1) && (val != NAND_RESERVED_2)) {
+			src = BOOT_DEVICE_IFC_NAND;
+			INFO("RCW BOOT SRC is IFC NAND\n");
+		}
+	} else {
+		/* RCW SRC NOR */
+		val = rcw_src & RCW_SRC_NOR_MASK;
+		if (val == NOR_8B_VAL || val == NOR_16B_VAL) {
+			src = BOOT_DEVICE_IFC_NOR;
+			INFO("RCW BOOT SRC is IFC NOR\n");
+		} else {
+			switch (rcw_src) {
+			case QSPI_VAL1:
+			case QSPI_VAL2:
+				src = BOOT_DEVICE_QSPI;
+				INFO("RCW BOOT SRC is QSPI\n");
+				break;
+			case SD_VAL:
+				src = BOOT_DEVICE_EMMC;
+				INFO("RCW BOOT SRC is SD/EMMC\n");
+				break;
+			default:
+				src = BOOT_DEVICE_NONE;
+			}
+		}
+	}
+
+	return src;
+}
+
+/* This function sets up access permissions on memory regions */
+void soc_mem_access(void)
+{
+	dram_regions_info_t *info_dram_regions = get_dram_regions_info();
+	struct tzc400_reg tzc400_reg_list[MAX_NUM_TZC_REGION];
+	unsigned int dram_idx, index = 0U;
+
+	for (dram_idx = 0U; dram_idx < info_dram_regions->num_dram_regions;
+			dram_idx++) {
+		if (info_dram_regions->region[dram_idx].size == 0) {
+			ERROR("DDR init failure, or");
+			ERROR("DRAM regions not populated correctly.\n");
+			break;
+		}
+
+		index = populate_tzc400_reg_list(tzc400_reg_list,
+				dram_idx, index,
+				info_dram_regions->region[dram_idx].addr,
+				info_dram_regions->region[dram_idx].size,
+				NXP_SECURE_DRAM_SIZE, NXP_SP_SHRD_DRAM_SIZE);
+	}
+
+	mem_access_setup(NXP_TZC_ADDR, index, tzc400_reg_list);
+}
+
+#else /* IMAGE_BL2 */
+/* Functions for BL31 */
+
+const unsigned char _power_domain_tree_desc[] = {1, 1, 4};
+
+CASSERT(NUMBER_OF_CLUSTERS && NUMBER_OF_CLUSTERS <= 256,
+		assert_invalid_ls1046_cluster_count);
+
+/* This function returns the SoC topology */
+const unsigned char *plat_get_power_domain_tree_desc(void)
+{
+	return _power_domain_tree_desc;
+}
+
+/*
+ * This function returns the core count within the cluster corresponding to
+ * `mpidr`.
+ */
+unsigned int plat_ls_get_cluster_core_count(u_register_t mpidr)
+{
+	return CORES_PER_CLUSTER;
+}
+
+void soc_early_platform_setup2(void)
+{
+	dcfg_init(&dcfg_init_data);
+	/* Initialize system level generic timer for SoCs */
+	delay_timer_init(NXP_TIMER_ADDR);
+
+#if LOG_LEVEL > 0
+	/* Initialize the console to provide early debug support */
+	plat_console_init(NXP_CONSOLE_ADDR,
+				NXP_UART_CLK_DIVIDER, NXP_CONSOLE_BAUDRATE);
+#endif
+}
+
+void soc_platform_setup(void)
+{
+	static uint32_t target_mask_array[PLATFORM_CORE_COUNT];
+	/*
+	 * On a GICv2 system, the Group 1 secure interrupts are treated
+	 * as Group 0 interrupts.
+	 */
+	static interrupt_prop_t ls_interrupt_props[] = {
+		PLAT_LS_G1S_IRQ_PROPS(GICV2_INTR_GROUP0),
+		PLAT_LS_G0_IRQ_PROPS(GICV2_INTR_GROUP0)
+	};
+
+	plat_ls_gic_driver_init(
+#if (TEST_BL31)
+	/* Defect in simulator - GIC base addresses (4Kb aligned) */
+			NXP_GICD_4K_ADDR,
+			NXP_GICC_4K_ADDR,
+#else
+			NXP_GICD_64K_ADDR,
+			NXP_GICC_64K_ADDR,
+#endif
+			PLATFORM_CORE_COUNT,
+			ls_interrupt_props,
+			ARRAY_SIZE(ls_interrupt_props),
+			target_mask_array);
+
+	plat_ls_gic_init();
+	enable_init_timer();
+}
+
+/* This function initializes the soc from the BL31 module */
+void soc_init(void)
+{
+	 /* low-level init of the soc */
+	soc_init_lowlevel();
+	_init_global_data();
+	soc_init_percpu();
+	_initialize_psci();
+
+	/*
+	 * Initialize the interconnect during cold boot.
+	 * No need for locks as no other CPU is active.
+	 */
+	cci_init(NXP_CCI_ADDR, cci_map, ARRAY_SIZE(cci_map));
+
+	/*
+	 * Enable coherency in interconnect for the primary CPU's cluster.
+	 * Earlier bootloader stages might already do this but we can't
+	 * assume so. No harm in executing this code twice.
+	 */
+	cci_enable_snoop_dvm_reqs(MPIDR_AFFLVL1_VAL(read_mpidr()));
+
+	/* Init CSU to enable non-secure access to peripherals */
+	enable_layerscape_ns_access(ns_dev, ARRAY_SIZE(ns_dev), NXP_CSU_ADDR);
+
+	/* Initialize the crypto accelerator if enabled */
+	if (is_sec_enabled() == false) {
+		INFO("SEC is disabled.\n");
+	} else {
+		sec_init(NXP_CAAM_ADDR);
+	}
+}
+
+void soc_runtime_setup(void)
+{
+
+}
+
+#endif /* IMAGE_BL2 */
diff --git a/plat/nxp/soc-ls1046a/soc.def b/plat/nxp/soc-ls1046a/soc.def
new file mode 100644
index 0000000..e6b37c0
--- /dev/null
+++ b/plat/nxp/soc-ls1046a/soc.def
@@ -0,0 +1,107 @@
+#
+# Copyright 2022 NXP
+#
+# SPDX-License-Identifier: BSD-3-Clause
+#
+#
+#------------------------------------------------------------------------------
+#
+# This file contains the basic architecture definitions that drive the build
+#
+# -----------------------------------------------------------------------------
+
+CORE_TYPE	:=	a72
+
+CACHE_LINE	:=	6
+
+# set to GIC400 or GIC500
+GIC		:=	GIC400
+
+# set to CCI400 or CCN504 or CCN508
+INTERCONNECT	:=	CCI400
+
+# indicate layerscape chassis level - set to 3=LSCH3 or 2=LSCH2
+CHASSIS		:=	2
+
+# TZC IP Details TZC used is TZC380 or TZC400
+TZC_ID		:=	TZC400
+
+# CONSOLE Details available is NS16550 or PL011
+CONSOLE		:=	NS16550
+
+ # Select the DDR PHY generation to be used
+PLAT_DDR_PHY	:=      PHY_GEN1
+
+PHYS_SYS	:=	64
+
+# ddr controller - set to MMDC or NXP
+DDRCNTLR	:=	NXP
+
+# ddr phy - set to NXP or SNPS
+DDRPHY		:=	NXP
+
+# Area of OCRAM reserved by ROM code
+NXP_ROM_RSVD	:= 0x5900
+
+# Max Size of CSF header. Required to define BL2 TEXT LIMIT in soc.def
+# Input to CST create_hdr_esbc tool
+CSF_HDR_SZ	:= 0x3000
+
+# In IMAGE_BL2, compile time flag for handling Cache coherency
+# with CAAM for BL2 running from OCRAM
+SEC_MEM_NON_COHERENT	:= yes
+
+# OCRAM MAP
+OCRAM_START_ADDR	:=	0x10000000
+OCRAM_SIZE		:=	0x20000
+
+# BL2 binary is placed at  start of OCRAM.
+# Also used by create_pbl.mk.
+BL2_BASE		:=	0x10000000
+
+# After BL2 bin, OCRAM is used by ROM Code:
+# (OCRAM_START_ADDR + BL2_BIN_SIZE) ->  (NXP_ROM_RSVD - 1)
+
+# After ROM Code, OCRAM is used by CSF header.
+# (OCRAM_START_ADDR + BL2_TEXT_LIMIT + NXP_ROM_RSVD) -> (CSF_HDR_SZ - 1)
+
+# BL2_HDR_LOC has to be (OCRAM_START_ADDR + OCRAM_SIZE - NXP_ROM_RSVD - CSF_HDR_SZ)
+# This value should be greater than BL2_TEXT_LIMIT
+# Input to CST create_hdr_isbc tool
+BL2_HDR_LOC_HDR		?=	$(shell echo $$(( $(OCRAM_START_ADDR) + $(OCRAM_SIZE) - $(NXP_ROM_RSVD) - $(CSF_HDR_SZ))))
+# Covert to HEX to be used by create_pbl.mk
+BL2_HDR_LOC		:=	$$(echo "obase=16; ${BL2_HDR_LOC_HDR}" | bc)
+
+# Core Errata
+ERRATA_A72_859971	:=	1
+
+# SoC ERRATAS
+ERRATA_SOC_A008850	:=      1
+ERRATA_SOC_A010539	:= 	1
+
+# DDR Errata
+ERRATA_DDR_A008511	:=	1
+ERRATA_DDR_A009803	:=	1
+ERRATA_DDR_A009942	:=	1
+ERRATA_DDR_A010165	:=	1
+
+# enable dynamic memory mapping
+PLAT_XLAT_TABLES_DYNAMIC :=	1
+
+# Define Endianness of each module
+NXP_GUR_ENDIANNESS	:=	BE
+NXP_DDR_ENDIANNESS	:=	BE
+NXP_SEC_ENDIANNESS	:=	BE
+NXP_SFP_ENDIANNESS	:=	BE
+NXP_SNVS_ENDIANNESS	:=	BE
+NXP_ESDHC_ENDIANNESS	:=	BE
+NXP_QSPI_ENDIANNESS	:=	BE
+NXP_FSPI_ENDIANNESS	:=	BE
+NXP_SCFG_ENDIANNESS	:=	BE
+NXP_GPIO_ENDIANNESS	:=	BE
+NXP_IFC_ENDIANNESS	:=	BE
+
+NXP_SFP_VER		:= 3_2
+
+# OCRAM ECC Enabled
+OCRAM_ECC_EN		:=	yes
diff --git a/plat/nxp/soc-ls1046a/soc.mk b/plat/nxp/soc-ls1046a/soc.mk
new file mode 100644
index 0000000..8207dcd
--- /dev/null
+++ b/plat/nxp/soc-ls1046a/soc.mk
@@ -0,0 +1,114 @@
+#
+# Copyright 2018-2022 NXP
+#
+# SPDX-License-Identifier: BSD-3-Clause
+#
+
+# SoC-specific build parameters
+SOC		:=	ls1046a
+PLAT_PATH	:=	plat/nxp
+PLAT_COMMON_PATH:=	plat/nxp/common
+PLAT_DRIVERS_PATH:=	drivers/nxp
+PLAT_SOC_PATH	:=	${PLAT_PATH}/soc-${SOC}
+BOARD_PATH	:=	${PLAT_SOC_PATH}/${BOARD}
+
+# Get SoC-specific defnitions
+include ${PLAT_SOC_PATH}/soc.def
+include ${PLAT_COMMON_PATH}/plat_make_helper/soc_common_def.mk
+include ${PLAT_COMMON_PATH}/plat_make_helper/plat_build_macros.mk
+
+# For Security Features
+DISABLE_FUSE_WRITE	:= 1
+ifeq (${TRUSTED_BOARD_BOOT}, 1)
+$(eval $(call SET_NXP_MAKE_FLAG,SMMU_NEEDED,BL2))
+$(eval $(call SET_NXP_MAKE_FLAG,SFP_NEEDED,BL2))
+$(eval $(call SET_NXP_MAKE_FLAG,SNVS_NEEDED,BL2))
+SECURE_BOOT	:= yes
+endif
+$(eval $(call SET_NXP_MAKE_FLAG,CRYPTO_NEEDED,BL_COMM))
+
+# Selecting Drivers for SoC
+$(eval $(call SET_NXP_MAKE_FLAG,DCFG_NEEDED,BL_COMM))
+$(eval $(call SET_NXP_MAKE_FLAG,CSU_NEEDED,BL_COMM))
+$(eval $(call SET_NXP_MAKE_FLAG,TIMER_NEEDED,BL_COMM))
+$(eval $(call SET_NXP_MAKE_FLAG,INTERCONNECT_NEEDED,BL_COMM))
+$(eval $(call SET_NXP_MAKE_FLAG,GIC_NEEDED,BL31))
+$(eval $(call SET_NXP_MAKE_FLAG,CONSOLE_NEEDED,BL_COMM))
+$(eval $(call SET_NXP_MAKE_FLAG,PMU_NEEDED,BL_COMM))
+$(eval $(call SET_NXP_MAKE_FLAG,DDR_DRIVER_NEEDED,BL2))
+$(eval $(call SET_NXP_MAKE_FLAG,TZASC_NEEDED,BL2))
+$(eval $(call SET_NXP_MAKE_FLAG,I2C_NEEDED,BL2))
+$(eval $(call SET_NXP_MAKE_FLAG,IMG_LOADR_NEEDED,BL2))
+
+# Selecting PSCI & SIP_SVC support
+$(eval $(call SET_NXP_MAKE_FLAG,PSCI_NEEDED,BL31))
+$(eval $(call SET_NXP_MAKE_FLAG,SIPSVC_NEEDED,BL31))
+
+# Source File Addition
+PLAT_INCLUDES		+=	-I${PLAT_COMMON_PATH}/include/default\
+				-I${BOARD_PATH}\
+				-I${PLAT_COMMON_PATH}/include/default/ch_${CHASSIS}\
+				-I${PLAT_SOC_PATH}/include\
+				-I${PLAT_COMMON_PATH}/soc_errata
+
+ifeq (${SECURE_BOOT},yes)
+include ${PLAT_COMMON_PATH}/tbbr/tbbr.mk
+endif
+
+ifeq ($(WARM_BOOT),yes)
+include ${PLAT_COMMON_PATH}/warm_reset/warm_reset.mk
+endif
+
+ifeq (${NXP_NV_SW_MAINT_LAST_EXEC_DATA}, yes)
+include ${PLAT_COMMON_PATH}/nv_storage/nv_storage.mk
+endif
+
+ifeq (${PSCI_NEEDED}, yes)
+include ${PLAT_COMMON_PATH}/psci/psci.mk
+endif
+
+ifeq (${SIPSVC_NEEDED}, yes)
+include ${PLAT_COMMON_PATH}/sip_svc/sipsvc.mk
+endif
+
+# For fuse-fip & fuse-programming
+ifeq (${FUSE_PROG}, 1)
+include ${PLAT_COMMON_PATH}/fip_handler/fuse_fip/fuse.mk
+endif
+
+ifeq (${IMG_LOADR_NEEDED},yes)
+include $(PLAT_COMMON_PATH)/img_loadr/img_loadr.mk
+endif
+
+# Adding source files for the above selected drivers.
+include ${PLAT_DRIVERS_PATH}/drivers.mk
+
+# Adding SoC specific files
+include ${PLAT_COMMON_PATH}/soc_errata/errata.mk
+
+PLAT_INCLUDES		+=	${NV_STORAGE_INCLUDES}\
+				${WARM_RST_INCLUDES}
+
+BL31_SOURCES		+=	${PLAT_SOC_PATH}/$(ARCH)/${SOC}.S\
+				${WARM_RST_BL31_SOURCES}\
+				${PSCI_SOURCES}\
+				${SIPSVC_SOURCES}\
+				${PLAT_COMMON_PATH}/$(ARCH)/bl31_data.S
+
+PLAT_BL_COMMON_SOURCES	+=	${PLAT_COMMON_PATH}/$(ARCH)/ls_helpers.S\
+				${PLAT_SOC_PATH}/aarch64/${SOC}_helpers.S\
+				${NV_STORAGE_SOURCES}\
+				${WARM_RST_BL_COMM_SOURCES}\
+				${PLAT_SOC_PATH}/soc.c
+
+ifeq (${TEST_BL31}, 1)
+BL31_SOURCES		+=	${PLAT_SOC_PATH}/$(ARCH)/bootmain64.S\
+				${PLAT_SOC_PATH}/$(ARCH)/nonboot64.S
+endif
+
+BL2_SOURCES		+=	${DDR_CNTLR_SOURCES}\
+				${TBBR_SOURCES}\
+				${FUSE_SOURCES}
+
+# Adding TFA setup files
+include ${PLAT_PATH}/common/setup/common.mk