library/ecp_invasive.h

/**
 * \file ecp_invasive.h
 *
 * \brief ECP module: interfaces for invasive testing only.
 *
 * The interfaces in this file are intended for testing purposes only.
 * They SHOULD NOT be made available in library integrations except when
 * building the library for testing.
 */
/*
 *  Copyright The Mbed TLS Contributors
 *  SPDX-License-Identifier: Apache-2.0
 *
 *  Licensed under the Apache License, Version 2.0 (the "License"); you may
 *  not use this file except in compliance with the License.
 *  You may obtain a copy of the License at
 *
 *  http://www.apache.org/licenses/LICENSE-2.0
 *
 *  Unless required by applicable law or agreed to in writing, software
 *  distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
 *  WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 *  See the License for the specific language governing permissions and
 *  limitations under the License.
 */
#ifndef MBEDTLS_ECP_INVASIVE_H
#define MBEDTLS_ECP_INVASIVE_H

#include "common.h"
#include "mbedtls/bignum.h"
#include "bignum_mod.h"
#include "mbedtls/ecp.h"

/*
 * Curve modulus types
 */
typedef enum {
    MBEDTLS_ECP_MOD_NONE = 0,
    MBEDTLS_ECP_MOD_COORDINATE,
    MBEDTLS_ECP_MOD_SCALAR
} mbedtls_ecp_modulus_type;

/* Requred macros for ECP split.
 * If MBEDTLS_ECP_WITH_MPI_UINT is defined the new bignum interface is used.
 */
#ifndef MBEDTLS_ECP_WITH_MPI_UINT

/* Because of `check_names.py` a define is needed for every macro. */
//#define MBEDTLS_ECP_WITH_MPI_UINT

/* Enable the old bignum interface. */
#define MBEDTLS_ECP_WITH_MPI_STRUCT
#endif

typedef enum {
    MBEDTLS_ECP_VARIANT_NONE            = 0,
    MBEDTLS_ECP_VARIANT_WITH_MPI_STRUCT = 1,
    MBEDTLS_ECP_VARIANT_WITH_MPI_UINT   = 2
} mbedtls_ecp_variant;

#if defined(MBEDTLS_TEST_HOOKS) && defined(MBEDTLS_ECP_LIGHT)

/** Queries the ecp variant.
 *
 * \return  The id of the ecp variant.
 */
MBEDTLS_STATIC_TESTABLE
mbedtls_ecp_variant mbedtls_ecp_get_variant(void);

#if defined(MBEDTLS_ECP_MONTGOMERY_ENABLED)
/** Generate a private key on a Montgomery curve (Curve25519 or Curve448).
 *
 * This function implements key generation for the set of secret keys
 * specified in [Curve25519] p. 5 and in [Curve448]. The resulting value
 * has the lower bits masked but is not necessarily canonical.
 *
 * \note            - [Curve25519] http://cr.yp.to/ecdh/curve25519-20060209.pdf
 *                  - [RFC7748] https://tools.ietf.org/html/rfc7748
 *
 * \p high_bit      The position of the high-order bit of the key to generate.
 *                  This is the bit-size of the key minus 1:
 *                  254 for Curve25519 or 447 for Curve448.
 * \param d         The randomly generated key. This is a number of size
 *                  exactly \p high_bit + 1 bits, with the least significant bits
 *                  masked as specified in [Curve25519] and in [RFC7748] §5.
 * \param f_rng     The RNG function.
 * \param p_rng     The RNG context to be passed to \p f_rng.
 *
 * \return          \c 0 on success.
 * \return          \c MBEDTLS_ERR_ECP_xxx or MBEDTLS_ERR_MPI_xxx on failure.
 */
int mbedtls_ecp_gen_privkey_mx(size_t high_bit,
                               mbedtls_mpi *d,
                               int (*f_rng)(void *, unsigned char *, size_t),
                               void *p_rng);

#endif /* MBEDTLS_ECP_MONTGOMERY_ENABLED */

#if defined(MBEDTLS_ECP_DP_SECP192R1_ENABLED)

/** Fast quasi-reduction modulo p192 (FIPS 186-3 D.2.1)
 *
 * This operation expects a 384 bit MPI and the result of the reduction
 * is a 192 bit MPI.
 *
 * \param[in,out]   Np  The address of the MPI to be converted.
 *                      Must have twice as many limbs as the modulus.
 *                      Upon return this holds the reduced value. The bitlength
 *                      of the reduced value is the same as that of the modulus
 *                      (192 bits).
 * \param[in]       Nn  The length of \p Np in limbs.
 */
MBEDTLS_STATIC_TESTABLE
int mbedtls_ecp_mod_p192_raw(mbedtls_mpi_uint *Np, size_t Nn);

#endif /* MBEDTLS_ECP_DP_SECP192R1_ENABLED */

#if defined(MBEDTLS_ECP_DP_SECP224R1_ENABLED)

/** Fast quasi-reduction modulo p224 (FIPS 186-3 D.2.2)
 *
 * \param[in,out]   X       The address of the MPI to be converted.
 *                          Must have exact limb size that stores a 448-bit MPI
 *                          (double the bitlength of the modulus).
 *                          Upon return holds the reduced value which is
 *                          in range `0 <= X < 2 * N` (where N is the modulus).
 *                          The bitlength of the reduced value is the same as
 *                          that of the modulus (224 bits).
 * \param[in]       X_limbs The length of \p X in limbs.
 *
 * \return          \c 0 on success.
 * \return          #MBEDTLS_ERR_ECP_BAD_INPUT_DATA if \p X_limbs is not the
 *                  limb size that sores a 448-bit MPI.
 */
MBEDTLS_STATIC_TESTABLE
int mbedtls_ecp_mod_p224_raw(mbedtls_mpi_uint *X, size_t X_limbs);

#endif /* MBEDTLS_ECP_DP_SECP224R1_ENABLED */

#if defined(MBEDTLS_ECP_DP_SECP256R1_ENABLED)

/** Fast quasi-reduction modulo p256 (FIPS 186-3 D.2.3)
 *
 * \param[in,out]   X       The address of the MPI to be converted.
 *                          Must have exact limb size that stores a 512-bit MPI
 *                          (double the bitlength of the modulus).
 *                          Upon return holds the reduced value which is
 *                          in range `0 <= X < 2 * N` (where N is the modulus).
 *                          The bitlength of the reduced value is the same as
 *                          that of the modulus (256 bits).
 * \param[in]       X_limbs The length of \p X in limbs.
 *
 * \return          \c 0 on success.
 * \return          #MBEDTLS_ERR_ECP_BAD_INPUT_DATA if \p X_limbs is not the
 *                  limb size that sores a 512-bit MPI.
 */
MBEDTLS_STATIC_TESTABLE
int mbedtls_ecp_mod_p256_raw(mbedtls_mpi_uint *X, size_t X_limbs);

#endif

#if defined(MBEDTLS_ECP_DP_SECP521R1_ENABLED)

/** Fast quasi-reduction modulo p521 = 2^521 - 1 (FIPS 186-3 D.2.5)
 *
 * \param[in,out]   X       The address of the MPI to be converted.
 *                          Must have twice as many limbs as the modulus
 *                          (the modulus is 521 bits long). Upon return this
 *                          holds the reduced value. The reduced value is
 *                          in range `0 <= X < 2 * N` (where N is the modulus).
 *                          and its the bitlength is one plus the bitlength
 *                          of the modulus.
 * \param[in]       X_limbs The length of \p X in limbs.
 *
 * \return          \c 0 on success.
 * \return          #MBEDTLS_ERR_ECP_BAD_INPUT_DATA if \p X_limbs does not have
 *                  twice as many limbs as the modulus.
 */
MBEDTLS_STATIC_TESTABLE
int mbedtls_ecp_mod_p521_raw(mbedtls_mpi_uint *X, size_t X_limbs);

#endif /* MBEDTLS_ECP_DP_SECP521R1_ENABLED */

#if defined(MBEDTLS_ECP_DP_SECP384R1_ENABLED)

/** Fast quasi-reduction modulo p384 (FIPS 186-3 D.2.4)
 *
 * \param[in,out]   X       The address of the MPI to be converted.
 *                          Must have exact limb size that stores a 768-bit MPI
 *                          (double the bitlength of the modulus).
 *                          Upon return holds the reduced value which is
 *                          in range `0 <= X < 2 * N` (where N is the modulus).
 *                          The bitlength of the reduced value is the same as
 *                          that of the modulus (384 bits).
 * \param[in]       X_limbs The length of \p N in limbs.
 *
 * \return          \c 0 on success.
 * \return          #MBEDTLS_ERR_ECP_BAD_INPUT_DATA if \p N_n does not have
 *                  twice as many limbs as the modulus.
 */
MBEDTLS_STATIC_TESTABLE
int  mbedtls_ecp_mod_p384_raw(mbedtls_mpi_uint *X, size_t X_limbs);

#endif /* MBEDTLS_ECP_DP_SECP384R1_ENABLED */

#if defined(MBEDTLS_ECP_DP_SECP192K1_ENABLED)

/** Fast quasi-reduction modulo p192k1 = 2^192 - R,
 * with R = 2^32 + 2^12 + 2^8 + 2^7 + 2^6 + 2^3 + 1 = 0x01000011C9
 *
 * \param[in,out]   X       The address of the MPI to be converted.
 *                          Must have exact limb size that stores a 384-bit MPI
 *                          (double the bitlength of the modulus).
 *                          Upon return holds the reduced value which is
 *                          in range `0 <= X < 2 * N` (where N is the modulus).
 *                          The bitlength of the reduced value is the same as
 *                          that of the modulus (192 bits).
 * \param[in]       X_limbs The length of \p X in limbs.
 *
 * \return          \c 0 on success.
 * \return          #MBEDTLS_ERR_ECP_BAD_INPUT_DATA if \p X does not have
 *                  twice as many limbs as the modulus.
 * \return          #MBEDTLS_ERR_ECP_ALLOC_FAILED if memory allocation failed.
 */
MBEDTLS_STATIC_TESTABLE
int mbedtls_ecp_mod_p192k1_raw(mbedtls_mpi_uint *X, size_t X_limbs);

#endif /* MBEDTLS_ECP_DP_SECP192K1_ENABLED */

#if defined(MBEDTLS_ECP_DP_SECP224K1_ENABLED)

/** Fast quasi-reduction modulo p224k1 = 2^224 - R,
 * with R = 2^32 + 2^12 + 2^11 + 2^9 + 2^7 + 2^4 + 2 + 1 = 0x0100001A93
 *
 * \param[in,out]   X       The address of the MPI to be converted.
 *                          Must have exact limb size that stores a 448-bit MPI
 *                          (double the bitlength of the modulus).
 *                          Upon return holds the reduced value which is
 *                          in range `0 <= X < 2 * N` (where N is the modulus).
 *                          The bitlength of the reduced value is the same as
 *                          that of the modulus (224 bits).
 * \param[in]       X_limbs The length of \p X in limbs.
 *
 * \return          \c 0 on success.
 * \return          #MBEDTLS_ERR_ECP_BAD_INPUT_DATA if \p X does not have
 *                  twice as many limbs as the modulus.
 * \return          #MBEDTLS_ERR_ECP_ALLOC_FAILED if memory allocation failed.
 */
MBEDTLS_STATIC_TESTABLE
int mbedtls_ecp_mod_p224k1_raw(mbedtls_mpi_uint *X, size_t X_limbs);

#endif /* MBEDTLS_ECP_DP_SECP224K1_ENABLED */

#if defined(MBEDTLS_ECP_DP_SECP256K1_ENABLED)

/** Fast quasi-reduction modulo p256k1 = 2^256 - R,
 * with R = 2^32 + 2^9 + 2^8 + 2^7 + 2^6 + 2^4 + 1 = 0x01000003D1
 *
 * \param[in,out]   X       The address of the MPI to be converted.
 *                          Must have exact limb size that stores a 512-bit MPI
 *                          (double the bitlength of the modulus).
 *                          Upon return holds the reduced value which is
 *                          in range `0 <= X < 2 * N` (where N is the modulus).
 *                          The bitlength of the reduced value is the same as
 *                          that of the modulus (256 bits).
 * \param[in]       X_limbs The length of \p X in limbs.
 *
 * \return          \c 0 on success.
 * \return          #MBEDTLS_ERR_ECP_BAD_INPUT_DATA if \p X does not have
 *                  twice as many limbs as the modulus.
 * \return          #MBEDTLS_ERR_ECP_ALLOC_FAILED if memory allocation failed.
 */
MBEDTLS_STATIC_TESTABLE
int mbedtls_ecp_mod_p256k1_raw(mbedtls_mpi_uint *X, size_t X_limbs);

#endif /* MBEDTLS_ECP_DP_SECP256K1_ENABLED */

#if defined(MBEDTLS_ECP_DP_CURVE25519_ENABLED)

/** Fast quasi-reduction modulo p255 = 2^255 - 19
 *
 * \param[in,out]   X       The address of the MPI to be converted.
 *                          Must have exact limb size that stores a 510-bit MPI
 *                          (double the bitlength of the modulus).
 *                          Upon return holds the reduced value which is
 *                          in range `0 <= X < 2 * N` (where N is the modulus).
 * \param[in]       X_limbs The length of \p X in limbs.
 *
 * \return          \c 0 on success.
 * \return          #MBEDTLS_ERR_ECP_BAD_INPUT_DATA if \p X does not have
 *                  twice as many limbs as the modulus.
 * \return          #MBEDTLS_ERR_ECP_ALLOC_FAILED if memory allocation failed.
 */
MBEDTLS_STATIC_TESTABLE
int mbedtls_ecp_mod_p255_raw(mbedtls_mpi_uint *X, size_t X_limbs);

#endif /* MBEDTLS_ECP_DP_CURVE25519_ENABLED */

#if defined(MBEDTLS_ECP_DP_CURVE448_ENABLED)

/** Fast quasi-reduction modulo p448 = 2^448 - 2^224 - 1
 * Write X as A0 + 2^448 A1 and A1 as B0 + 2^224 B1, and return A0 + A1 + B1 +
 * (B0 + B1) * 2^224.
 *
 * \param[in,out]   X       The address of the MPI to be converted.
 *                          Must have exact limb size that stores a 896-bit MPI
 *                          (double the bitlength of the modulus). Upon return
 *                          holds the reduced value which is in range `0 <= X <
 *                          N` (where N is the modulus). The bitlength of the
 *                          reduced value is the same as that of the modulus
 *                          (448 bits).
 * \param[in]       X_limbs The length of \p X in limbs.
 *
 * \return          \c 0 on Success.
 * \return          #MBEDTLS_ERR_ECP_BAD_INPUT_DATA if \p X does not have
 *                  twice as many limbs as the modulus.
 * \return          #MBEDTLS_ERR_ECP_ALLOC_FAILED if memory allocation
 *                  failed.
 */
MBEDTLS_STATIC_TESTABLE
int mbedtls_ecp_mod_p448_raw(mbedtls_mpi_uint *X, size_t X_limbs);

#endif /* MBEDTLS_ECP_DP_CURVE448_ENABLED */

/** Initialise a modulus with hard-coded const curve data.
 *
 * \note            The caller is responsible for the \p N modulus' memory.
 *                  mbedtls_mpi_mod_modulus_free(&N) should be invoked at the
 *                  end of its lifecycle.
 *
 * \param[in,out] N The address of the modulus structure to populate.
 *                  Must be initialized.
 * \param[in] id    The mbedtls_ecp_group_id for which to initialise the modulus.
 * \param[in] ctype The mbedtls_ecp_modulus_type identifier for a coordinate modulus (P)
 *                  or a scalar modulus (N).
 *
 * \return          \c 0 if successful.
 * \return          #MBEDTLS_ERR_ECP_BAD_INPUT_DATA if the given MPIs do not
 *                  have the correct number of limbs.
 *
 */
MBEDTLS_STATIC_TESTABLE
int mbedtls_ecp_modulus_setup(mbedtls_mpi_mod_modulus *N,
                              const mbedtls_ecp_group_id id,
                              const mbedtls_ecp_modulus_type ctype);

#endif /* MBEDTLS_TEST_HOOKS && MBEDTLS_ECP_C */

#endif /* MBEDTLS_ECP_INVASIVE_H */