diff --git a/docs/plat/arm/fvp/index.rst b/docs/plat/arm/fvp/index.rst
new file mode 100644
index 0000000..b6396b9
--- /dev/null
+++ b/docs/plat/arm/fvp/index.rst
@@ -0,0 +1,637 @@
+Arm Fixed Virtual Platforms (FVP)
+=================================
+
+Fixed Virtual Platform (FVP) Support
+------------------------------------
+
+This section lists the supported Arm |FVP| platforms. Please refer to the FVP
+documentation for a detailed description of the model parameter options.
+
+The latest version of the AArch64 build of TF-A has been tested on the following
+Arm FVPs without shifted affinities, and that do not support threaded CPU cores
+(64-bit host machine only).
+
+.. note::
+   The FVP models used are Version 11.6 Build 45, unless otherwise stated.
+
+-  ``FVP_Base_AEMv8A-AEMv8A``
+-  ``FVP_Base_AEMv8A-AEMv8A-AEMv8A-AEMv8A-CCN502``
+-  ``FVP_Base_RevC-2xAEMv8A``
+-  ``FVP_Base_Cortex-A32x4``
+-  ``FVP_Base_Cortex-A35x4``
+-  ``FVP_Base_Cortex-A53x4``
+-  ``FVP_Base_Cortex-A55x4+Cortex-A75x4``
+-  ``FVP_Base_Cortex-A55x4``
+-  ``FVP_Base_Cortex-A57x1-A53x1``
+-  ``FVP_Base_Cortex-A57x2-A53x4``
+-  ``FVP_Base_Cortex-A57x4-A53x4``
+-  ``FVP_Base_Cortex-A57x4``
+-  ``FVP_Base_Cortex-A72x4-A53x4``
+-  ``FVP_Base_Cortex-A72x4``
+-  ``FVP_Base_Cortex-A73x4-A53x4``
+-  ``FVP_Base_Cortex-A73x4``
+-  ``FVP_Base_Cortex-A75x4``
+-  ``FVP_Base_Cortex-A76x4``
+-  ``FVP_Base_Cortex-A76AEx4``
+-  ``FVP_Base_Cortex-A76AEx8``
+-  ``FVP_Base_Cortex-A77x4`` (Version 11.7 build 36)
+-  ``FVP_Base_Neoverse-N1x4``
+-  ``FVP_Base_Zeusx4``
+-  ``FVP_CSS_SGI-575`` (Version 11.3 build 42)
+-  ``FVP_CSS_SGM-775`` (Version 11.3 build 42)
+-  ``FVP_RD_E1Edge`` (Version 11.3 build 42)
+-  ``FVP_RD_N1Edge``
+-  ``Foundation_Platform``
+
+The latest version of the AArch32 build of TF-A has been tested on the
+following Arm FVPs without shifted affinities, and that do not support threaded
+CPU cores (64-bit host machine only).
+
+-  ``FVP_Base_AEMv8A-AEMv8A``
+-  ``FVP_Base_Cortex-A32x4``
+
+.. note::
+   The ``FVP_Base_RevC-2xAEMv8A`` FVP only supports shifted affinities, which
+   is not compatible with legacy GIC configurations. Therefore this FVP does not
+   support these legacy GIC configurations.
+
+The *Foundation* and *Base* FVPs can be downloaded free of charge. See the `Arm
+FVP website`_. The Cortex-A models listed above are also available to download
+from `Arm's website`_.
+
+.. note::
+   The build numbers quoted above are those reported by launching the FVP
+   with the ``--version`` parameter.
+
+.. note::
+   Linaro provides a ramdisk image in prebuilt FVP configurations and full
+   file systems that can be downloaded separately. To run an FVP with a virtio
+   file system image an additional FVP configuration option
+   ``-C bp.virtioblockdevice.image_path="<path-to>/<file-system-image>`` can be
+   used.
+
+.. note::
+   The software will not work on Version 1.0 of the Foundation FVP.
+   The commands below would report an ``unhandled argument`` error in this case.
+
+.. note::
+   FVPs can be launched with ``--cadi-server`` option such that a
+   CADI-compliant debugger (for example, Arm DS-5) can connect to and control
+   its execution.
+
+.. warning::
+   Since FVP model Version 11.0 Build 11.0.34 and Version 8.5 Build 0.8.5202
+   the internal synchronisation timings changed compared to older versions of
+   the models. The models can be launched with ``-Q 100`` option if they are
+   required to match the run time characteristics of the older versions.
+
+All the above platforms have been tested with `Linaro Release 19.06`_.
+
+.. _build_options_arm_fvp_platform:
+
+Arm FVP Platform Specific Build Options
+---------------------------------------
+
+-  ``FVP_CLUSTER_COUNT`` : Configures the cluster count to be used to
+   build the topology tree within TF-A. By default TF-A is configured for dual
+   cluster topology and this option can be used to override the default value.
+
+-  ``FVP_INTERCONNECT_DRIVER``: Selects the interconnect driver to be built. The
+   default interconnect driver depends on the value of ``FVP_CLUSTER_COUNT`` as
+   explained in the options below:
+
+   -  ``FVP_CCI`` : The CCI driver is selected. This is the default
+      if 0 < ``FVP_CLUSTER_COUNT`` <= 2.
+   -  ``FVP_CCN`` : The CCN driver is selected. This is the default
+      if ``FVP_CLUSTER_COUNT`` > 2.
+
+-  ``FVP_MAX_CPUS_PER_CLUSTER``: Sets the maximum number of CPUs implemented in
+   a single cluster.  This option defaults to 4.
+
+-  ``FVP_MAX_PE_PER_CPU``: Sets the maximum number of PEs implemented on any CPU
+   in the system. This option defaults to 1. Note that the build option
+   ``ARM_PLAT_MT`` doesn't have any effect on FVP platforms.
+
+-  ``FVP_USE_GIC_DRIVER`` : Selects the GIC driver to be built. Options:
+
+   -  ``FVP_GIC600`` : The GIC600 implementation of GICv3 is selected
+   -  ``FVP_GICV2`` : The GICv2 only driver is selected
+   -  ``FVP_GICV3`` : The GICv3 only driver is selected (default option)
+
+-  ``FVP_USE_SP804_TIMER`` : Use the SP804 timer instead of the Generic Timer
+   for functions that wait for an arbitrary time length (udelay and mdelay).
+   The default value is 0.
+
+-  ``FVP_HW_CONFIG_DTS`` : Specify the path to the DTS file to be compiled
+   to DTB and packaged in FIP as the HW_CONFIG. See :ref:`Firmware Design` for
+   details on HW_CONFIG. By default, this is initialized to a sensible DTS
+   file in ``fdts/`` folder depending on other build options. But some cases,
+   like shifted affinity format for MPIDR, cannot be detected at build time
+   and this option is needed to specify the appropriate DTS file.
+
+-  ``FVP_HW_CONFIG`` : Specify the path to the HW_CONFIG blob to be packaged in
+   FIP. See :ref:`Firmware Design` for details on HW_CONFIG. This option is
+   similar to the ``FVP_HW_CONFIG_DTS`` option, but it directly specifies the
+   HW_CONFIG blob instead of the DTS file. This option is useful to override
+   the default HW_CONFIG selected by the build system.
+
+Booting Firmware Update images
+------------------------------
+
+When Firmware Update (FWU) is enabled there are at least 2 new images
+that have to be loaded, the Non-Secure FWU ROM (NS-BL1U), and the
+FWU FIP.
+
+The additional fip images must be loaded with:
+
+::
+
+    --data cluster0.cpu0="<path_to>/ns_bl1u.bin"@0x0beb8000	[ns_bl1u_base_address]
+    --data cluster0.cpu0="<path_to>/fwu_fip.bin"@0x08400000	[ns_bl2u_base_address]
+
+The address ns_bl1u_base_address is the value of NS_BL1U_BASE.
+In the same way, the address ns_bl2u_base_address is the value of
+NS_BL2U_BASE.
+
+Booting an EL3 payload
+----------------------
+
+The EL3 payloads boot flow requires the CPU's mailbox to be cleared at reset for
+the secondary CPUs holding pen to work properly. Unfortunately, its reset value
+is undefined on the FVP platform and the FVP platform code doesn't clear it.
+Therefore, one must modify the way the model is normally invoked in order to
+clear the mailbox at start-up.
+
+One way to do that is to create an 8-byte file containing all zero bytes using
+the following command:
+
+.. code:: shell
+
+    dd if=/dev/zero of=mailbox.dat bs=1 count=8
+
+and pre-load it into the FVP memory at the mailbox address (i.e. ``0x04000000``)
+using the following model parameters:
+
+::
+
+    --data cluster0.cpu0=mailbox.dat@0x04000000   [Base FVPs]
+    --data=mailbox.dat@0x04000000                 [Foundation FVP]
+
+To provide the model with the EL3 payload image, the following methods may be
+used:
+
+#. If the EL3 payload is able to execute in place, it may be programmed into
+   flash memory. On Base Cortex and AEM FVPs, the following model parameter
+   loads it at the base address of the NOR FLASH1 (the NOR FLASH0 is already
+   used for the FIP):
+
+   ::
+
+       -C bp.flashloader1.fname="<path-to>/<el3-payload>"
+
+   On Foundation FVP, there is no flash loader component and the EL3 payload
+   may be programmed anywhere in flash using method 3 below.
+
+#. When using the ``SPIN_ON_BL1_EXIT=1`` loading method, the following DS-5
+   command may be used to load the EL3 payload ELF image over JTAG:
+
+   ::
+
+       load <path-to>/el3-payload.elf
+
+#. The EL3 payload may be pre-loaded in volatile memory using the following
+   model parameters:
+
+   ::
+
+       --data cluster0.cpu0="<path-to>/el3-payload>"@address   [Base FVPs]
+       --data="<path-to>/<el3-payload>"@address                [Foundation FVP]
+
+   The address provided to the FVP must match the ``EL3_PAYLOAD_BASE`` address
+   used when building TF-A.
+
+Booting a preloaded kernel image (Base FVP)
+-------------------------------------------
+
+The following example uses a simplified boot flow by directly jumping from the
+TF-A to the Linux kernel, which will use a ramdisk as filesystem. This can be
+useful if both the kernel and the device tree blob (DTB) are already present in
+memory (like in FVP).
+
+For example, if the kernel is loaded at ``0x80080000`` and the DTB is loaded at
+address ``0x82000000``, the firmware can be built like this:
+
+.. code:: shell
+
+    CROSS_COMPILE=aarch64-linux-gnu-  \
+    make PLAT=fvp DEBUG=1             \
+    RESET_TO_BL31=1                   \
+    ARM_LINUX_KERNEL_AS_BL33=1        \
+    PRELOADED_BL33_BASE=0x80080000    \
+    ARM_PRELOADED_DTB_BASE=0x82000000 \
+    all fip
+
+Now, it is needed to modify the DTB so that the kernel knows the address of the
+ramdisk. The following script generates a patched DTB from the provided one,
+assuming that the ramdisk is loaded at address ``0x84000000``. Note that this
+script assumes that the user is using a ramdisk image prepared for U-Boot, like
+the ones provided by Linaro. If using a ramdisk without this header,the ``0x40``
+offset in ``INITRD_START`` has to be removed.
+
+.. code:: bash
+
+    #!/bin/bash
+
+    # Path to the input DTB
+    KERNEL_DTB=<path-to>/<fdt>
+    # Path to the output DTB
+    PATCHED_KERNEL_DTB=<path-to>/<patched-fdt>
+    # Base address of the ramdisk
+    INITRD_BASE=0x84000000
+    # Path to the ramdisk
+    INITRD=<path-to>/<ramdisk.img>
+
+    # Skip uboot header (64 bytes)
+    INITRD_START=$(printf "0x%x" $((${INITRD_BASE} + 0x40)) )
+    INITRD_SIZE=$(stat -Lc %s ${INITRD})
+    INITRD_END=$(printf "0x%x" $((${INITRD_BASE} + ${INITRD_SIZE})) )
+
+    CHOSEN_NODE=$(echo                                        \
+    "/ {                                                      \
+            chosen {                                          \
+                    linux,initrd-start = <${INITRD_START}>;   \
+                    linux,initrd-end = <${INITRD_END}>;       \
+            };                                                \
+    };")
+
+    echo $(dtc -O dts -I dtb ${KERNEL_DTB}) ${CHOSEN_NODE} |  \
+            dtc -O dtb -o ${PATCHED_KERNEL_DTB} -
+
+And the FVP binary can be run with the following command:
+
+.. code:: shell
+
+    <path-to>/FVP_Base_AEMv8A-AEMv8A                            \
+    -C pctl.startup=0.0.0.0                                     \
+    -C bp.secure_memory=1                                       \
+    -C cluster0.NUM_CORES=4                                     \
+    -C cluster1.NUM_CORES=4                                     \
+    -C cache_state_modelled=1                                   \
+    -C cluster0.cpu0.RVBAR=0x04020000                           \
+    -C cluster0.cpu1.RVBAR=0x04020000                           \
+    -C cluster0.cpu2.RVBAR=0x04020000                           \
+    -C cluster0.cpu3.RVBAR=0x04020000                           \
+    -C cluster1.cpu0.RVBAR=0x04020000                           \
+    -C cluster1.cpu1.RVBAR=0x04020000                           \
+    -C cluster1.cpu2.RVBAR=0x04020000                           \
+    -C cluster1.cpu3.RVBAR=0x04020000                           \
+    --data cluster0.cpu0="<path-to>/bl31.bin"@0x04020000        \
+    --data cluster0.cpu0="<path-to>/<patched-fdt>"@0x82000000   \
+    --data cluster0.cpu0="<path-to>/<kernel-binary>"@0x80080000 \
+    --data cluster0.cpu0="<path-to>/<ramdisk.img>"@0x84000000
+
+Obtaining the Flattened Device Trees
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+Depending on the FVP configuration and Linux configuration used, different
+FDT files are required. FDT source files for the Foundation and Base FVPs can
+be found in the TF-A source directory under ``fdts/``. The Foundation FVP has
+a subset of the Base FVP components. For example, the Foundation FVP lacks
+CLCD and MMC support, and has only one CPU cluster.
+
+.. note::
+   It is not recommended to use the FDTs built along the kernel because not
+   all FDTs are available from there.
+
+The dynamic configuration capability is enabled in the firmware for FVPs.
+This means that the firmware can authenticate and load the FDT if present in
+FIP. A default FDT is packaged into FIP during the build based on
+the build configuration. This can be overridden by using the ``FVP_HW_CONFIG``
+or ``FVP_HW_CONFIG_DTS`` build options (refer to
+:ref:`build_options_arm_fvp_platform` for details on the options).
+
+-  ``fvp-base-gicv2-psci.dts``
+
+   For use with models such as the Cortex-A57-A53 Base FVPs without shifted
+   affinities and with Base memory map configuration.
+
+-  ``fvp-base-gicv2-psci-aarch32.dts``
+
+   For use with models such as the Cortex-A32 Base FVPs without shifted
+   affinities and running Linux in AArch32 state with Base memory map
+   configuration.
+
+-  ``fvp-base-gicv3-psci.dts``
+
+   For use with models such as the Cortex-A57-A53 Base FVPs without shifted
+   affinities and with Base memory map configuration and Linux GICv3 support.
+
+-  ``fvp-base-gicv3-psci-1t.dts``
+
+   For use with models such as the AEMv8-RevC Base FVP with shifted affinities,
+   single threaded CPUs, Base memory map configuration and Linux GICv3 support.
+
+-  ``fvp-base-gicv3-psci-dynamiq.dts``
+
+   For use with models as the Cortex-A55-A75 Base FVPs with shifted affinities,
+   single cluster, single threaded CPUs, Base memory map configuration and Linux
+   GICv3 support.
+
+-  ``fvp-base-gicv3-psci-aarch32.dts``
+
+   For use with models such as the Cortex-A32 Base FVPs without shifted
+   affinities and running Linux in AArch32 state with Base memory map
+   configuration and Linux GICv3 support.
+
+-  ``fvp-foundation-gicv2-psci.dts``
+
+   For use with Foundation FVP with Base memory map configuration.
+
+-  ``fvp-foundation-gicv3-psci.dts``
+
+   (Default) For use with Foundation FVP with Base memory map configuration
+   and Linux GICv3 support.
+
+
+Running on the Foundation FVP with reset to BL1 entrypoint
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+The following ``Foundation_Platform`` parameters should be used to boot Linux with
+4 CPUs using the AArch64 build of TF-A.
+
+.. code:: shell
+
+    <path-to>/Foundation_Platform                   \
+    --cores=4                                       \
+    --arm-v8.0                                      \
+    --secure-memory                                 \
+    --visualization                                 \
+    --gicv3                                         \
+    --data="<path-to>/<bl1-binary>"@0x0             \
+    --data="<path-to>/<FIP-binary>"@0x08000000      \
+    --data="<path-to>/<kernel-binary>"@0x80080000   \
+    --data="<path-to>/<ramdisk-binary>"@0x84000000
+
+Notes:
+
+-  BL1 is loaded at the start of the Trusted ROM.
+-  The Firmware Image Package is loaded at the start of NOR FLASH0.
+-  The firmware loads the FDT packaged in FIP to the DRAM. The FDT load address
+   is specified via the ``hw_config_addr`` property in `TB_FW_CONFIG for FVP`_.
+-  The default use-case for the Foundation FVP is to use the ``--gicv3`` option
+   and enable the GICv3 device in the model. Note that without this option,
+   the Foundation FVP defaults to legacy (Versatile Express) memory map which
+   is not supported by TF-A.
+-  In order for TF-A to run correctly on the Foundation FVP, the architecture
+   versions must match. The Foundation FVP defaults to the highest v8.x
+   version it supports but the default build for TF-A is for v8.0. To avoid
+   issues either start the Foundation FVP to use v8.0 architecture using the
+   ``--arm-v8.0`` option, or build TF-A with an appropriate value for
+   ``ARM_ARCH_MINOR``.
+
+Running on the AEMv8 Base FVP with reset to BL1 entrypoint
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+The following ``FVP_Base_RevC-2xAEMv8A`` parameters should be used to boot Linux
+with 8 CPUs using the AArch64 build of TF-A.
+
+.. code:: shell
+
+    <path-to>/FVP_Base_RevC-2xAEMv8A                            \
+    -C pctl.startup=0.0.0.0                                     \
+    -C bp.secure_memory=1                                       \
+    -C bp.tzc_400.diagnostics=1                                 \
+    -C cluster0.NUM_CORES=4                                     \
+    -C cluster1.NUM_CORES=4                                     \
+    -C cache_state_modelled=1                                   \
+    -C bp.secureflashloader.fname="<path-to>/<bl1-binary>"      \
+    -C bp.flashloader0.fname="<path-to>/<FIP-binary>"           \
+    --data cluster0.cpu0="<path-to>/<kernel-binary>"@0x80080000 \
+    --data cluster0.cpu0="<path-to>/<ramdisk>"@0x84000000
+
+.. note::
+   The ``FVP_Base_RevC-2xAEMv8A`` has shifted affinities and requires
+   a specific DTS for all the CPUs to be loaded.
+
+Running on the AEMv8 Base FVP (AArch32) with reset to BL1 entrypoint
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+The following ``FVP_Base_AEMv8A-AEMv8A`` parameters should be used to boot Linux
+with 8 CPUs using the AArch32 build of TF-A.
+
+.. code:: shell
+
+    <path-to>/FVP_Base_AEMv8A-AEMv8A                            \
+    -C pctl.startup=0.0.0.0                                     \
+    -C bp.secure_memory=1                                       \
+    -C bp.tzc_400.diagnostics=1                                 \
+    -C cluster0.NUM_CORES=4                                     \
+    -C cluster1.NUM_CORES=4                                     \
+    -C cache_state_modelled=1                                   \
+    -C cluster0.cpu0.CONFIG64=0                                 \
+    -C cluster0.cpu1.CONFIG64=0                                 \
+    -C cluster0.cpu2.CONFIG64=0                                 \
+    -C cluster0.cpu3.CONFIG64=0                                 \
+    -C cluster1.cpu0.CONFIG64=0                                 \
+    -C cluster1.cpu1.CONFIG64=0                                 \
+    -C cluster1.cpu2.CONFIG64=0                                 \
+    -C cluster1.cpu3.CONFIG64=0                                 \
+    -C bp.secureflashloader.fname="<path-to>/<bl1-binary>"      \
+    -C bp.flashloader0.fname="<path-to>/<FIP-binary>"           \
+    --data cluster0.cpu0="<path-to>/<kernel-binary>"@0x80080000 \
+    --data cluster0.cpu0="<path-to>/<ramdisk>"@0x84000000
+
+Running on the Cortex-A57-A53 Base FVP with reset to BL1 entrypoint
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+The following ``FVP_Base_Cortex-A57x4-A53x4`` model parameters should be used to
+boot Linux with 8 CPUs using the AArch64 build of TF-A.
+
+.. code:: shell
+
+    <path-to>/FVP_Base_Cortex-A57x4-A53x4                       \
+    -C pctl.startup=0.0.0.0                                     \
+    -C bp.secure_memory=1                                       \
+    -C bp.tzc_400.diagnostics=1                                 \
+    -C cache_state_modelled=1                                   \
+    -C bp.secureflashloader.fname="<path-to>/<bl1-binary>"      \
+    -C bp.flashloader0.fname="<path-to>/<FIP-binary>"           \
+    --data cluster0.cpu0="<path-to>/<kernel-binary>"@0x80080000 \
+    --data cluster0.cpu0="<path-to>/<ramdisk>"@0x84000000
+
+Running on the Cortex-A32 Base FVP (AArch32) with reset to BL1 entrypoint
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+The following ``FVP_Base_Cortex-A32x4`` model parameters should be used to
+boot Linux with 4 CPUs using the AArch32 build of TF-A.
+
+.. code:: shell
+
+    <path-to>/FVP_Base_Cortex-A32x4                             \
+    -C pctl.startup=0.0.0.0                                     \
+    -C bp.secure_memory=1                                       \
+    -C bp.tzc_400.diagnostics=1                                 \
+    -C cache_state_modelled=1                                   \
+    -C bp.secureflashloader.fname="<path-to>/<bl1-binary>"      \
+    -C bp.flashloader0.fname="<path-to>/<FIP-binary>"           \
+    --data cluster0.cpu0="<path-to>/<kernel-binary>"@0x80080000 \
+    --data cluster0.cpu0="<path-to>/<ramdisk>"@0x84000000
+
+
+Running on the AEMv8 Base FVP with reset to BL31 entrypoint
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+The following ``FVP_Base_RevC-2xAEMv8A`` parameters should be used to boot Linux
+with 8 CPUs using the AArch64 build of TF-A.
+
+.. code:: shell
+
+    <path-to>/FVP_Base_RevC-2xAEMv8A                             \
+    -C pctl.startup=0.0.0.0                                      \
+    -C bp.secure_memory=1                                        \
+    -C bp.tzc_400.diagnostics=1                                  \
+    -C cluster0.NUM_CORES=4                                      \
+    -C cluster1.NUM_CORES=4                                      \
+    -C cache_state_modelled=1                                    \
+    -C cluster0.cpu0.RVBAR=0x04010000                            \
+    -C cluster0.cpu1.RVBAR=0x04010000                            \
+    -C cluster0.cpu2.RVBAR=0x04010000                            \
+    -C cluster0.cpu3.RVBAR=0x04010000                            \
+    -C cluster1.cpu0.RVBAR=0x04010000                            \
+    -C cluster1.cpu1.RVBAR=0x04010000                            \
+    -C cluster1.cpu2.RVBAR=0x04010000                            \
+    -C cluster1.cpu3.RVBAR=0x04010000                            \
+    --data cluster0.cpu0="<path-to>/<bl31-binary>"@0x04010000    \
+    --data cluster0.cpu0="<path-to>/<bl32-binary>"@0xff000000    \
+    --data cluster0.cpu0="<path-to>/<bl33-binary>"@0x88000000    \
+    --data cluster0.cpu0="<path-to>/<fdt>"@0x82000000            \
+    --data cluster0.cpu0="<path-to>/<kernel-binary>"@0x80080000  \
+    --data cluster0.cpu0="<path-to>/<ramdisk>"@0x84000000
+
+Notes:
+
+-  If Position Independent Executable (PIE) support is enabled for BL31
+   in this config, it can be loaded at any valid address for execution.
+
+-  Since a FIP is not loaded when using BL31 as reset entrypoint, the
+   ``--data="<path-to><bl31|bl32|bl33-binary>"@<base-address-of-binary>``
+   parameter is needed to load the individual bootloader images in memory.
+   BL32 image is only needed if BL31 has been built to expect a Secure-EL1
+   Payload. For the same reason, the FDT needs to be compiled from the DT source
+   and loaded via the ``--data cluster0.cpu0="<path-to>/<fdt>"@0x82000000``
+   parameter.
+
+-  The ``FVP_Base_RevC-2xAEMv8A`` has shifted affinities and requires a
+   specific DTS for all the CPUs to be loaded.
+
+-  The ``-C cluster<X>.cpu<Y>.RVBAR=@<base-address-of-bl31>`` parameter, where
+   X and Y are the cluster and CPU numbers respectively, is used to set the
+   reset vector for each core.
+
+-  Changing the default value of ``ARM_TSP_RAM_LOCATION`` will also require
+   changing the value of
+   ``--data="<path-to><bl32-binary>"@<base-address-of-bl32>`` to the new value of
+   ``BL32_BASE``.
+
+
+Running on the AEMv8 Base FVP (AArch32) with reset to SP_MIN entrypoint
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+The following ``FVP_Base_AEMv8A-AEMv8A`` parameters should be used to boot Linux
+with 8 CPUs using the AArch32 build of TF-A.
+
+.. code:: shell
+
+    <path-to>/FVP_Base_AEMv8A-AEMv8A                             \
+    -C pctl.startup=0.0.0.0                                      \
+    -C bp.secure_memory=1                                        \
+    -C bp.tzc_400.diagnostics=1                                  \
+    -C cluster0.NUM_CORES=4                                      \
+    -C cluster1.NUM_CORES=4                                      \
+    -C cache_state_modelled=1                                    \
+    -C cluster0.cpu0.CONFIG64=0                                  \
+    -C cluster0.cpu1.CONFIG64=0                                  \
+    -C cluster0.cpu2.CONFIG64=0                                  \
+    -C cluster0.cpu3.CONFIG64=0                                  \
+    -C cluster1.cpu0.CONFIG64=0                                  \
+    -C cluster1.cpu1.CONFIG64=0                                  \
+    -C cluster1.cpu2.CONFIG64=0                                  \
+    -C cluster1.cpu3.CONFIG64=0                                  \
+    -C cluster0.cpu0.RVBAR=0x04002000                            \
+    -C cluster0.cpu1.RVBAR=0x04002000                            \
+    -C cluster0.cpu2.RVBAR=0x04002000                            \
+    -C cluster0.cpu3.RVBAR=0x04002000                            \
+    -C cluster1.cpu0.RVBAR=0x04002000                            \
+    -C cluster1.cpu1.RVBAR=0x04002000                            \
+    -C cluster1.cpu2.RVBAR=0x04002000                            \
+    -C cluster1.cpu3.RVBAR=0x04002000                            \
+    --data cluster0.cpu0="<path-to>/<bl32-binary>"@0x04002000    \
+    --data cluster0.cpu0="<path-to>/<bl33-binary>"@0x88000000    \
+    --data cluster0.cpu0="<path-to>/<fdt>"@0x82000000            \
+    --data cluster0.cpu0="<path-to>/<kernel-binary>"@0x80080000  \
+    --data cluster0.cpu0="<path-to>/<ramdisk>"@0x84000000
+
+.. note::
+   The load address of ``<bl32-binary>`` depends on the value ``BL32_BASE``.
+   It should match the address programmed into the RVBAR register as well.
+
+Running on the Cortex-A57-A53 Base FVP with reset to BL31 entrypoint
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+The following ``FVP_Base_Cortex-A57x4-A53x4`` model parameters should be used to
+boot Linux with 8 CPUs using the AArch64 build of TF-A.
+
+.. code:: shell
+
+    <path-to>/FVP_Base_Cortex-A57x4-A53x4                        \
+    -C pctl.startup=0.0.0.0                                      \
+    -C bp.secure_memory=1                                        \
+    -C bp.tzc_400.diagnostics=1                                  \
+    -C cache_state_modelled=1                                    \
+    -C cluster0.cpu0.RVBARADDR=0x04010000                        \
+    -C cluster0.cpu1.RVBARADDR=0x04010000                        \
+    -C cluster0.cpu2.RVBARADDR=0x04010000                        \
+    -C cluster0.cpu3.RVBARADDR=0x04010000                        \
+    -C cluster1.cpu0.RVBARADDR=0x04010000                        \
+    -C cluster1.cpu1.RVBARADDR=0x04010000                        \
+    -C cluster1.cpu2.RVBARADDR=0x04010000                        \
+    -C cluster1.cpu3.RVBARADDR=0x04010000                        \
+    --data cluster0.cpu0="<path-to>/<bl31-binary>"@0x04010000    \
+    --data cluster0.cpu0="<path-to>/<bl32-binary>"@0xff000000    \
+    --data cluster0.cpu0="<path-to>/<bl33-binary>"@0x88000000    \
+    --data cluster0.cpu0="<path-to>/<fdt>"@0x82000000            \
+    --data cluster0.cpu0="<path-to>/<kernel-binary>"@0x80080000  \
+    --data cluster0.cpu0="<path-to>/<ramdisk>"@0x84000000
+
+Running on the Cortex-A32 Base FVP (AArch32) with reset to SP_MIN entrypoint
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+The following ``FVP_Base_Cortex-A32x4`` model parameters should be used to
+boot Linux with 4 CPUs using the AArch32 build of TF-A.
+
+.. code:: shell
+
+    <path-to>/FVP_Base_Cortex-A32x4                             \
+    -C pctl.startup=0.0.0.0                                     \
+    -C bp.secure_memory=1                                       \
+    -C bp.tzc_400.diagnostics=1                                 \
+    -C cache_state_modelled=1                                   \
+    -C cluster0.cpu0.RVBARADDR=0x04002000                       \
+    -C cluster0.cpu1.RVBARADDR=0x04002000                       \
+    -C cluster0.cpu2.RVBARADDR=0x04002000                       \
+    -C cluster0.cpu3.RVBARADDR=0x04002000                       \
+    --data cluster0.cpu0="<path-to>/<bl32-binary>"@0x04002000   \
+    --data cluster0.cpu0="<path-to>/<bl33-binary>"@0x88000000   \
+    --data cluster0.cpu0="<path-to>/<fdt>"@0x82000000           \
+    --data cluster0.cpu0="<path-to>/<kernel-binary>"@0x80080000 \
+    --data cluster0.cpu0="<path-to>/<ramdisk>"@0x84000000
+
+--------------
+
+*Copyright (c) 2019, Arm Limited. All rights reserved.*
+
+.. _TB_FW_CONFIG for FVP: ../plat/arm/board/fvp/fdts/fvp_tb_fw_config.dts
+.. _Arm's website: `FVP models`_
+.. _FVP models: https://developer.arm.com/products/system-design/fixed-virtual-platforms
+.. _Linaro Release 19.06: http://releases.linaro.org/members/arm/platforms/19.06
+.. _Arm FVP website: https://developer.arm.com/products/system-design/fixed-virtual-platforms