boot/zephyr/Kconfig.serial_recovery

# Copyright (c) 2017-2020 Linaro Limited
# Copyright (c) 2020 Arm Limited
# Copyright (c) 2017-2022 Nordic Semiconductor ASA
#
# SPDX-License-Identifier: Apache-2.0


menuconfig MCUBOOT_SERIAL
	bool "MCUboot serial recovery"
	default n
	select REBOOT
	select GPIO
	select SERIAL
	select UART_INTERRUPT_DRIVEN
	select BASE64
	select CRC
	help
	  If y, enables a serial-port based update mode. This allows
	  MCUboot itself to load update images into flash over a UART.
	  If unsure, leave at the default value.

if MCUBOOT_SERIAL

choice BOOT_SERIAL_DEVICE
	prompt "Serial device"
	default BOOT_SERIAL_UART if !BOARD_NRF52840DONGLE_NRF52840
	default BOOT_SERIAL_CDC_ACM if BOARD_NRF52840DONGLE_NRF52840

config BOOT_SERIAL_UART
	bool "UART"
	# SERIAL and UART_INTERRUPT_DRIVEN already selected

config BOOT_SERIAL_CDC_ACM
	bool "CDC ACM"
	select USB_DEVICE_STACK

endchoice

config MCUBOOT_SERIAL_DIRECT_IMAGE_UPLOAD
	bool "Allow to select image number for DFU"
	help
	  With the option enabled, the mcuboot serial recovery will
	  respect the "image" field in mcumgr image update frame
	  header.
	  The mapping of image number to partition is as follows:
	    0 -> default behaviour, same as 1;
	    1 -> image-0 (primary slot of the first image);
	    2 -> image-1 (secondary slot of the first image);
	    3 -> image-2;
	    4 -> image-3.
	  Note that 0 is default upload target when no explicit
	  selection is done.

config BOOT_SERIAL_UNALIGNED_BUFFER_SIZE
	int "Stack buffer for unaligned memory writes"
	default 64
	help
	  Specifies the stack usage for a buffer which is used for unaligned
	  memory access when data is written to a device with memory alignment
	  requirements. Set to 0 to disable.

config BOOT_MAX_LINE_INPUT_LEN
	int "Maximum input line length"
	default 512
	help
	  Maximum length of input serial port buffer.

config BOOT_SERIAL_MAX_RECEIVE_SIZE
	int "Maximum command line length"
	default 1024
	help
	  Maximum length of received commands via the serial port.

config BOOT_LINE_BUFS
	int "Number of receive buffers"
	range 2 128
	default 2
	help
	  Number of receive buffers for data received via the serial port.

config BOOT_SERIAL_DETECT_PORT
	string "GPIO device to trigger serial recovery mode (DEPRECATED)"
	default GPIO_0 if SOC_FAMILY_NRF
	help
	  Zephyr GPIO device that contains the pin used to trigger
	  serial recovery mode.

config BOOT_SERIAL_DETECT_PIN
	int "Pin to trigger serial recovery mode (DEPRECATED)"
	default 6 if BOARD_NRF9160DK_NRF9160
	default 11 if BOARD_NRF52840DK_NRF52840
	default 13 if BOARD_NRF52DK_NRF52832 || BOARD_NRF52833DK_NRF52833
	default 23 if BOARD_NRF5340PDK_NRF5340_CPUAPP || BOARD_NRF5340PDK_NRF5340_CPUAPP_NS || \
		BOARD_NRF5340DK_NRF5340_CPUAPP || BOARD_NRF5340DK_NRF5340_CPUAPP_NS
	default -1
	help
	  Pin on the serial detect port that triggers serial recovery mode.

config BOOT_SERIAL_DETECT_PIN_VAL
	int "Serial detect pin trigger value (DEPRECATED)"
	default 0
	range 0 1
	help
	  Logic value of the detect pin that triggers serial recovery
	  mode.

config BOOT_SERIAL_DETECT_DELAY
	int "Serial detect pin detection delay time [ms]"
	default 0
	help
	  Used to prevent the bootloader from loading on button press.
	  Useful for powering on when using the same button as
	  the one used to place the device in bootloader mode.

config BOOT_ERASE_PROGRESSIVELY
	bool "Erase flash progressively when receiving new firmware"
	default y if SOC_FAMILY_NRF
	help
	 If enabled, flash is erased as necessary when receiving new firmware,
	 instead of erasing the whole image slot at once. This is necessary
	 on some hardware that has long erase times, to prevent long wait
	 times at the beginning of the DFU process.

config BOOT_MGMT_ECHO
	bool "Enable echo command"
	help
	  if enabled, support for the mcumgr echo command is being added.

menuconfig ENABLE_MGMT_PERUSER
	bool "Enable system specific mcumgr commands"
	help
	  The option enables processing of system specific mcumgr commands;
	  system specific commands are within group MGMT_GROUP_ID_PERUSER (64)
	  and above, as defined within mcumgr library.
	  These are system specific command and system specific implementation
	  function is required to process these commands.

if ENABLE_MGMT_PERUSER
config BOOT_MGMT_CUSTOM_STORAGE_ERASE
	bool "Enable storage erase command"
	help
	  The option enables mcumgr command that allows to erase storage
	  partition.
	  Note that the storage partition needs to be defined, in DTS, otherwise
	  enabling the option will cause a compilation to fail.

config BOOT_MGMT_CUSTOM_IMG_LIST
	bool "Enable custom image list command"
	help
	  The option enables command which returns versions and installation
	  statuses (custom property) for all images.

endif # ENABLE_MGMT_PERUSER

config BOOT_SERIAL_ENCRYPT_EC256
	bool "Support for encrypted upgrade images using ECIES-P256 in serial recovery upload"
	default n
	help
	  If y, uploaded images via serial recovery can be decrypted
	  on the fly when upgrading to the primary slot. The
	  encryption mechanism used in this case is ECIES using primitives
	  described under "ECIES-P256 encryption" in docs/encrypted_images.md.

config BOOT_SERIAL_WAIT_FOR_DFU
	bool "Wait for a prescribed duration to see if DFU is invoked by receiving a mcumgr comand"
	depends on BOOT_SERIAL_UART || BOOT_SERIAL_CDC_ACM
	help
	  If y, MCUboot waits for a prescribed duration of time to allow
	  for DFU to be invoked. The serial recovery can be entered by receiving any
	  mcumgr command.

config BOOT_SERIAL_WAIT_FOR_DFU_TIMEOUT
	int "Duration to wait for the serial DFU timeout in ms"
	default 500
	depends on BOOT_SERIAL_WAIT_FOR_DFU
	help
	  timeout in ms for MCUboot to wait to allow for DFU to be invoked.

endif # MCUBOOT_SERIAL